Manual Elica ELISLIM (page 5 of 5) (English)

471238

Zoom out

Zoom in

1/5

Warning!

— The hood cannot be connected to the

flues of other appliances that run on

energy sources other than electricity.

— When the hood is used at the same time

as other appliances that run on energy

sources other than electricity, provision

must be made for an adequate supply of

air.

— No food must be cooked flambé

underneath the hood. The use of an

unprotected flame is dangerous for the

filters and could cause fires.

Therefore, never use an open flame under

the hood. When frying foods, never leave

the pan unattended because the cooking

oil could flare up.

— Please comply with the provisions set

forth by current regulations regarding the

ventilation of hoods.

— The manufacturers will not be held liable

for damage to the hood or fires due to the

failure to observe the above instructions.

Electric connection

Before completing any connections, make

sure the house voltage corresponds with

the voltage indicated on the data plate affixed

to the inside of the hood.

It is advisable to call a qualified technician to

make the electrical connection.

Hood Fitted with Plug

Insert the plug into a socket which complies

with current regulations.

If you intend to connect the hood directly to

the mains, remove the plug and fit an

approved bipolar switch with a minimum

contact opening of no less than 3mm.

If the plug is not accessible once it has been

inserted in the socket, it will, however, be

necessary to fit an approved bipolar switch

with a minimum contact opening of no less

than 3mm.

Appliance without Plug

Fit an approved plug or an approved bipolar

switch with a minimum contact opening of

3mm.

The manufacturers will not be held liable for

any problems caused by the user’s failure to

observer the above instructions.

Mounting the Hood

The diameter of the ventilation duct must be

the same as the that of the flange mounted

on the ventilation hole on the hood. The

horizontal sections of the ducting must be

installed at a slight angle (about 10%) to

facilitate venting the vapours and fumes

outdoors.

To mount the hood proceed as follows:

a. Drill holes in the bottom of the cabinet so

that they correspond with the holes (F) in

the hood used to fasten it to the cabinet.

Use the drilling template if it has been

provided (the edge with the arrow should

correspond with the back edge of the

cabinet - Fig. 7).

b. Drill a hole on the back and in the top of

the cabinet for the ventilation duct (a

good rule of thumb is to make the diameter

of the hole 15 mm larger than that of the

duct used).

c. Insert the C screws supplied with the

hood into the F holes and tighten the

hood to the cabinet (Fig. 7).

Assembly using side brackets

(if supplied)

The hood can also be mounted by means

of two brackets supplied with the hood.

To fix the hood in this way (Fig. 8-9), proceed

as follows:

a. Drill two holes Ø 2 mm on the two sides

of the cupboard from the inside using the

template Q supplied.

b. Fix the two brackets T to the upper side

of the hood using screws V 4,2 x 35 (the

position of the brackets can be adjusted

in width according to the thickness of the

cupboard panels).

c. Fix the hood, through the brackets already

mounted, on the inside of the cupboard

using screws Z 3,5 x 13 (two each side).

Adjusting the Pull-Out Drawer

The hood can be installed beneath cabinets

with varying depths. Adjustments for opening

and closing the drawer can be made based

on your specific needs.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elica ELISLIM in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elica ELISLIM Manual

Product: