EL-2645 / PI Wireless Motion PIR Detector Standard & Petimmune – Funkbewegungsmelder Standard & Haustierimmun - Détecteur de mouvement sans fil PIR Standard & Petimmune - Draadloze PIR Detector Standard & Petimmune
5IN1561
International Headquarters:
Electronics Line 3000 Ltd.
14 Hachoma St., 75655
Rishon Le Zion, Israel
Tel: (+972-3) 963-7777
Fax: (+972-3) 961-6584
All data is subject to change without prior notice techniques
In no event shall Electronics Line be liable for an amount in excess of EL3K’s original selling price of this product, for any loss or damage
whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.
Hereby, Electronics Line declares that this sensor/transmitter is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
06/2011 5IN1561
The EL-2645 / PI is a Wireless Motion PIR
Detector designed for use with Electronics Line
supervised wireless range of receivers.
Location of Detector
Consider the following before mounting the
detector:
Select a location from which the pattern of
the detector is most likely to be crossed
by a burglar, should there be a break in.
Do not place bulky objects in front of the
detector.
Avoid a location that comes in direct
contact with radiators, heating/cooling
ducts or air conditioners.
Do not place the detector in front of
windows subject to direct sunlight or
drafts.
Installation Instructions
1. Open the housing by removing the front
cover. To do so, insert a screwdriver in
the release slot (located at the bottom of
the detector between the front and back
cover). Turn the screwdriver 90º to
release the cover.
2. Remove the PCB by turning counter-
clockwise and removing the 'PCB Screw'.
Note: Do not touch the face of the PYRO
sensor.
3. Apply battery power by removing the
isolator that separates the battery from the
contacts on the battery holder.
4.Set the receiver to Registration mode and
cause Tamper or Alarm transmission. Wait for
the receiver to indicate that the transmitter has
been registered successfully. Write the
number of the zone and the transmitter
number (if applicable) on the sticker provided.
Affix the sticker inside the front cover for future
reference.
Note: Alternatively, the Detector can be
registered to the receiver by manually
entering the transmitter's serial
number.
5.Choose an appropriate mounting height from
2.2 –2.5 and test the transmitter from the exact
mounting position before permanently mounting
the unit.
Note: If you choose mounting height other
than recommended (which is not
advised), pleaseperform a walk test to
check the lens coverage. The
recommended mounting height is the
best in terms of detection area.
6. Knock out the mounting holes and attach
the base to the wall.
7. If using the rear tamper switch, insert a
screw into the rear tamper mounting hole
located in the center of the back cover –
see Figure 3. When the detector is
removed from the wall, the screw causes
the tamper release to break away from the
back cover and the rear tamper switch is
released.
8. Mount the PCB on the base cover and
replace the PCB Screw.
9. Replace the front cover.
DIP Switches Settings
Switch
1
PIR sensitivity
* Off: Low
On: High
2
Operation mode:
* Off: Normal mode – Every 3 minutes.
After each detection the sensor initiates
a three-minute delay during which
alarm transmissions will not be sent
On: Walk Test mode. An alarm
transmission is sent after each
detection
3
Supervision Time:
Off: As supervision message will be
sent to the alarm panel every 15
minutes
* On: As supervision message will be
sent to the alarm panel every 65
minutes
4
LED
Off: LED disabled
* On: LED enabled
*=Default
Operation Modes
Warm-up Time: The detector will need to warm up
for the first 90 seconds after applying power.
Walk Test Mode: A walk test is performed in order
to determine the lens coverage pattern of the
detector –see Figure 2. Walk Test mode cancels
the delay time between detections, enabling you to
perform an efficient walk test.
To walk test the detector:
1. Set DIP 2 to ON.
2. Walk across the scope of the detector
according to the detection pattern
selected.
3.Confirm that the LED activates and
deactivates accordingly. Wait for ten
seconds after each detection before
continuing the test.
4. After completing the walk test. Set DIP-
2 to OFF.
LED Indication
The LED indicator is lit every time a transmission
is made. To enable/disable LED indication, refer to
DIP Switch Setting section for the appropriate DIP-
switch setting.
Note: The LED should only be disabled after
successfully walk testing the detector.
Changing Lenses
To change a lens, release the cavity seal using a
small screwdriver and fix the new lens into place
with the smooth side facing outwards. Verify that
the word TOP is located at the top of the lens
(alternatively a notch may appear on the bottom
edge of the lens) before snapping the cavity seal
back into place.
Battery Replacement
In case of a low battery (2.5 V and below), the
sensor low battery condition is reported to the
Control System and low battery message is
displayed
To replace a battery: Open the housing by
removing the front cover (see Installation
Instructions), replace the battery, and close the
front cover.
Note:Close the front cover immediately after
each battery replacement.
Technical Specifications
Frequency: 868.35, 433.92 MHz
Power: 3.6V ½ AA Lithium Battery
Caution: Fire, explosion and severe burn hazard!
Do not recharge, disassemble or heat above 100°C.
Current Consumption: 30mA (transmission), 8µA
(standby)
Pyroelectric Sensor: Dual Element
Maximum Coverage: 14 x 14m
Adaptive Temperature Compensation
RFI Immunity: According to EN 50130-4
Operating Temperature: -10 - 40°C
Fire Protection: ABS Plastic Housing
Dimensions: 110 x 60 x 45mm
Figure 1: PCB
1.Battery Holder
2.Antenna
3.LED Indicator
4.PCB Screw
5.DIP Switch
6.Tamper Switch
7.Pyro Sensor
8.Back Tamper
Figure 2: Lens Coverage
Note:The diagram shows the coverage
pattern for the detector fitted with a standard
lens of EL2645.
EL2645-PI has limited detection at the ground
to ignore animals
Rear tamper mounting
hole
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Electronics Line EL-2645 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Electronics Line EL-2645 in the language / languages: English as an attachment in your email.
The manual is 0,27 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
