127328
94
Zoom out
Zoom in
Previous page
1/96
Next page
right to suit the installation by means of the
locknut. The locknut must be correctly
fitted to avoid water leaks.
Attention! NOT all dishwasher models of
have inlet and drain hoses provided with
a locknut. In this case, this facility is not
available.
If the appliance is connected to new pipes or
pipes which have not been used for a long
time, you should run the water for a few mi-
nutes before connecting the inlet hose.
DO NOT use connection hoses which
have previously been used on an old ap-
pliance.
This appliance has been fitted with safe-
ty features which will prevent the water
used in the appliance from returning
back into the drinking water system. This
appliance complies with the applicable
plumbing regulations.
Water drain connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink run-
ning into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
The waste connection must be at a height of
between 30 cm (minimum) and 100 cm
(maximum) from the bottom of the dishwash-
er.
The drain hose can face either to the right or
left of the dishwasher
Ensure the drain hose is not bent or squash-
ed as this could prevent or slow down the
discharge of water.
The sink plug must not be in place when the
machine is draining as this could cause the
water to syphon back into the machine.
If you use a drain hose extension it must be
no longer than 2 metres and its internal di-
ameter must be no smaller than the diameter
of the hose provided.
Likewise the internal diameter of the cou-
plings used for connections to the waste out-
let must be no smaller than the diameter of
the hose provided.
When connecting the drain hose to an under
sink trap spigot, the entire plastic mem-
brane (A) must be removed. Failure to re-
move all the membrane will result in food
particles building up over time eventually
blocking the dishwasher drain hose spigot
Our appliances are supplied with a se-
curity device to protect against the re-
turn of dirty water back into the machine.
If the spigot of your sink has a "no return
valve" incorporated this can prevent the
correct draining of your dishwasher. We
therefore advise you to remove it.
To avoid water leakage after installation
make sure that the water couplings are
tight.
Electrical connection
Warning! Safety standards require
the appliance to be earthed.
Prior to using the appliance for the
first time, ensure that the rated volt-
age and type of supply on the rating
plate match that of the supply where
the appliance is to be installed. The
fuse rating is also to be found on the
rating plate.
94 electrolux
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Electrolux esf 66710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Electrolux esf 66710 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info