664085
8
Zoom out
Zoom in
Previous page
1/32
Next page
1. Layout:
1: Torque adjustment facility
2: Bit holder
3: Forward / Reverse selector switch
4: On/Off switch
5: Battery pack
6: Battery charger
7: Selector switch for 1st/2nd gear
8: Pushlock button
9: Selecting drill or hammer mode
2. Safety information
Please refer to the booklet included in delivery for
the safety instructions.
3. Important information
Be sure to read the following information before you
use your cordless screwdriver for the first time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 1 hour.
2. Only ever use sharp drill bits and screwdriver bits
which are suitable for the purpose and in faultless
condition.
3. Always check for concealed electric cables and
gas and water pipes when drilling and screwing in
walls.
4. Starting up
Charging the NC battery pack
1. Take the rechargeable battery pack out of the
handle, pressing the pushlock buttons at the side
to do so.
2. Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in the socket.
3. Insert the battery pack in the battery charger. The
green LED will come on. Press the SET button to
charge the battery pack. The red LED will come
on to indicate that the battery pack is being
charged. The green LED will come on to indicate
that charging has been completed. Empty battery
packs will require approx. 1 hour for charging. The
temperature of the battery pack may rise slightly
during the charging operation. This is normal.
If the battery pack fails to become charged, please
check
whether there is voltage at the socket-outlet
whether there is proper contact at the charging
contacts on the charger.
If the battery still fails to become charged, please
return
the charger
the battery pack
to our Customer Service Department.
Timely recharging of the Ni-Cd battery pack is
recommended in the interest of long battery life.
Recharging is always necessary when you notice
that the power of the battery-powered
drill/screwdriver is decreasing.
Never allow the battery pack to discharge
completely. This will result in damage to the Ni-Cd
battery pack!
Adjusting the torque (1)
The battery-powered drill/screwdriver is equipped
with a 16-step mechanical torque adjustment facility.
The torque for a specific size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
on the type and hardness of material in question
on the type and length screws used
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
Drilling
For drilling purposes, move the set-collar to the last
step „Drill“ (Figure 1). In this setting the slip clutch is
inactive. The maximum torque is available in drilling
mode.
Selecting drill or hammer mode (9)
For normal drilling, turn the front set-collar to the
„drill“ symbol. For drilling with hammer action, turn
the front set-collar to the „hammer“ symbol and the
set-collar for torque adjustment to the „drill“ symbol.
Forward/Reverse switch (3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against being
switched on accidentally. You can choose between
clockwise and anticlockwise rotation. To avoid
causing damage to the gearing it is advisable to
6
GB
Anleitung BAS 24S-2A SPK 1 21.09.2005 15:37 Uhr Seite 6
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell BAS 24S-2A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell BAS 24S-2A in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Norwegian as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info