727492
20
Zoom out
Zoom in
Previous page
1/23
Next page
17
Troubleshooting continued
Issue Possible Cause Solution
My air conditioner is
not cooling at all
Unit is not operating in
cooling mode
Set the unit to be in
cooling mode, and
lower the set
temperature (pg. 11)
The compressor is not
on
The compressor may
take up to 3 minutes to
turn on, or longer if it is
too warm
The ambient
temperature is too high
Lower the room
temperature to be
below 90°F degrees
The filter may be dusty
or blocked
Clean the filters.
(pg. 15)
Blocked exhaust port Remove any
obstructions in the
exhaust hose and port
My air conditioner
blows cold air, but
does not lower the
room temperature
The unit is not vented The unit must be
vented. (pg. 4)
The area of the room
is too large
Minimize the size of
the area to be cooled,
i.e. adding a drop
ceiling. Use more than
one unit to cool the
area, or use a larger
unit
Open windows and
doors
Close any open doors
and windows
Too many heat
sources
Remove or shut off
additional heat
sources such as radio
equipment, servers,
etc.
The room/garage may
be inadequately
insulated
Properly insulate the
room to be cooled, i.e.
using fiberglass
The ambient
temperature is too high
The unit may not work
if the room
temperature is above
90°F
Direct sunlight is
heating the room
Close curtains or pull
down blinds, and
minimize the direct
sunlight into the room
The filter may be dusty
or blocked
Clean the filter and
replace it if needed
Dirty condenser coils Carefully vacuum the
coils clean
Obstructed air intake
or exhaust ports
Remove anything
blocking the ports
My unit displays an
Error Code
Sensor error or water
reservoir is full
Read “Error Codes”
section. (pg. 12)
NOTE: If the ambient
temperature is above 90°F
the unit may not blow cold
air.
TIP: Run the unit before it is
needed. For example, run
the unit in the morning
before the area gets hot,
and continue to run the unit
all day long in order to
maintain a low temperature.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edgestar PAC1401W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edgestar PAC1401W in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info