663880

EdgeCraft Chef-s Choice 310 Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
6
STAGE 2
The final operation is HONING, Stage 2. Using these slots, again take about three (3) seconds
per pass for a 6” blade. As in Stage 1, alternate each pull from one HONING slot to the other.
Do not apply downward pressure on knife in this stage. You should pull the blade through both
HONING slots four (4) to six (6) times. Complete HONING with eight (8) to twelve (12) fast pulls,
(one [1] second each), alternating between the left and right slots.
After sharpening, wipe the blade clean, test for sharpness and use. If the knife is not sharp
enough repeat Stages 1 and 2. Your knife should be razor sharp.
RESHARPENING
After normal use you can resharpen your knife quickly. Starting with SHARPENING (Stage 1)
make eight (8) to ten (10) passes through each slot, alternating left and right. Complete with
eight (8) fast passes each side in Stage 1 before moving to Stage 2. In HONING (Stage 2) make
four (4) to six (6) passes through each slot, alternating left and right. Complete with eight (8) fast
passes each side. In RESHARPENING you are removing only micro amounts of steel immediately
adjacent to the edge— a unique feature of Chef’sChoice
®
that allows you to resharpen often
without any concern for the life of your knife.
SUGGESTIONS
Chef’sChoice
®
Professional Model 310 is designed to produce incredibly sharp knife edges in a
fast and easy manner. To ensure that you obtain razor sharp edges we suggest:
1. “Breaking-in” Suggestions. “Breaking-in” can be likened to commercial sharpening to
produce a factory-like edge. This is a one time operation for each knife, but it is important to
“break-in” the knife adequately. It is relatively easy to determine what is adequate and avoid
needless removal of excessive steel from your blade edge. You need sharpen in Stage 1 only
until the knife edge on successive pulls develops a burr along its entire edge. You can verify
there has been sufficient sharpening by moving your finger carefully across and away from
the edge to feel for the burr. A burr will be present on that last unsharpened side. With a soft
steel knife (and most are soft) you will usually find a burr develops when you have pulled the
knife through Stage 1, 15 to 20 times on each side. With unusually hard steel knives you may
find it necessary to pass through Stage 1 more than twenty (20) times on each side. With
harder steel knives, the burr will not be as evident. Remember, in Resharpening you need
pass through Stage 1 only eight (8) to ten (10) times.
Stage 2. Four (4) to six (6) passes alternating through each slot, (left and right HONING slots). Apply no downward
pressure in Stage 2.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice 310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice 310 in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info