663883

EdgeCraft Chef-s Choice - EdgeSelect 120 Manual

10
Zoom out
Zoom in
Previous page
1/12
Next page
10
right and left slots of Stage 2, then make a series of pulls in Stage 3, alternating right and left slots.
Excessive use of Stage 2 will remove more metal along the edge than is necessary in order to
sharpen the teeth.
Because serrated blades are saw-like structures, the edges will never appear to be as “sharp” as
the edge on a straight edge knife. However, their tooth-like structure will, at times, help break the
skin on hard crusty foods and penetrate other materials such as cardboard.
STAGE 3 DRESS TOOL: CLEANING/ DRESSING OF STROPPING/ POLISHING DISKS—STAGE 3:
The Chef’sChoice
®
Model 120 is equipped with a built-in accessory to manually clean/ dress the
honing disks in Stage 3. In the event these disks become glazed with grease, food or sharpening
debris, they can be cleaned and reshaped by actuating the manual lever on the rear of the sharp-
ener. This lever is located within a recess as shown in Figure 13 on the left lower corner as you
face the rear of the Model 120.
To actuate the cleaning/dressing tool, make sure the power is on and simply press the small
lever in the recess to the right or left and hold for 3 seconds. Then press the lever in the opposite
direction and hold for 3 seconds. When the lever is moved in one direction, the dressing tool cleans
and reshapes the active surface of one stropping/polishing disk. By moving it in the opposite
direction, you clean the other disk.
Use this clean/dress accessory only if and when Stage 3 no longer appears to be sharpening well
or when it takes too many pulls to obtain a razor sharp edge. Using this tool removes material
from the surface of the Stage 3 disks and hence, if used excessively, will unnecessarily remove
too much of the abrasive surface - wearing the disks out prematurely. If that should occur, factory
replacement of the disks will become necessary.
If you clean knives regularly before sharpening, you will need to clean or dress the Stage 3 disks
only about once a year or even less frequently
Resharpening: (See Sections above.)
Resharpen straight edge knives whenever practical using Stage 3. When that fails to quickly
resharpen, return to Stage 2 and make one or two pairs of alternating pulls. Then return to Stage
3 where only one to two alternating pairs of pulls will be adequate to put a new razor-like edge on
the knife. Use Stage 1 as a first step in resharpening only if you wish to have more “bite” along the
edge or if the knife has been dulled excessively.
Resharpen serrated blades in Stage 3. (See sections above.)
Figure 13. Stage 3 disks can be cleaned if necessary.
Use infrequently. (See instructions.)
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - EdgeSelect 120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - EdgeSelect 120 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info