Manual Ebode eSD18 (page 4 of 36) (English, German, Dutch, French, Spanish, Norwegian)

611875

Zoom out

Zoom in

1/36

7-5-2013 4 ebode eSD18

4. Using the Smoke Detector

Installing the battery

Connect a 9-volt battery to the connector. Do not use a rechargeable battery. The battery

will fit only one way. Be sure the battery connector is securely attached. Place battery into

battery pocket (see picture 1.2).

Alarm

A continuous beeps will sound when smoke is detected. One “chirp” every 30 seconds will

be an indication that the battery is low or the unit is malfunctioning. In case of a low

battery level, replace the battery as soon as possible. As you install the battery, the unit

will sound “chirp” to indicate the battery is installed properly.

The red LED will flash in conjunction with the alarm beep. I.e., the red LED will flash during

an alarm and a low battery mode chirp.

Testing the detector

Press the test button on top of the smoke detector or on the inside “Test Button 1” (see

picture 1.2) for several seconds to test the detector’s electronics. The alarm will sound.

Note, Do this weekly to ensure correct functioning.

Technical Specifications

Input Voltage: DC 9V

Static Current: <30uA

Alarm Current: <30mA

Operating Temperature: -10° ~ 50°C

Operating Humidity: <95% RH

Installation Method: Ceiling mounted

Detecting Area: 60m2 (with 4 meters height)

LED Frequency: once per 5 seconds

Alarm Output: Sound & Flash Alarm

Sensor: Infrared Photocell

Sensitivity: m=0.15 – 0.5dB/m

Low Voltage Prompt: 7.5V

5. Registering the Detector with the BSS880 Home Protector & Console

The detector can be registered in two different modes, being either as a Remote or as a

Sensor, the difference between these mode is explained below.

Remote mode

When set to Remote mode, the detector will act as a remote, which means it will always

trigger an alarm as soon as a fault is detected. The state of the console, being Armed or

Disarmed, will make no difference. You can change the mode with the “Mode Selector

Switch” showed in picture 1.2. Modes: Up is Remote Mode, down is Sensor Mode. When the

detector stops detecting smoke it will disarm the consoles alarm automatically.

Sensor mode

In Sensor mode the smoke detector will act as a door/window sensor. When the alarm is

disarmed and smoke is detected the smoke detector will sound an alarm and the console

will sound a chime (if enabled in the console). When the alarm is armed in “Away Mode”

and the smoke detector detects smoke both the alarm of the smoke detector and the alarm

of the console will sound (console will only sound alarm if enabled in the console). The

alarm of the console needs to be disabled with either the consoles PIN code or a remote.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ebode eSD18 in the language / languages: English, German, Dutch, French, Spanish, Norwegian as an attachment in your email.

The manual is 0,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ebode eSD18 Manual

Product: