53409

EBERLE Instat+ 2R Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
User and installation guide
INSTAT
+
2R
Room Temperature Controller
468 931 003 114
06490047001 ISSD
╞
I. User Guide
Operation (Overview)
1. Principle of function
INSTAT
+
the programmable room thermostat allows you to set time periods (up to 6
per day) and temperatures to suit your own lifestyle. Once fully installed and powered
the device will automatically set the correct time and in auto mode will control your
heating system according to pre-set program 1 (see 7.). The temperature is controlled
by sensing air temperature, switching on the heating when the air temperature falls
below the thermostat setting and switching it off once this set temperature has been
reached.
NOTE:
The adjusted values (while programming) will be accepted automatically after ~5 sec.
2. How to insert batteries (2 AA 1,5V Alkaline)
3. Automatic mode (AUTO)
In this mode, the room temperature is automatically controlled according to the pre-
set program. The pointer indicating the mode is set to AUTO. The number at the
bottom right indicates the program event during the day. (Fig. 1)
4. How to change the temperature for a short period of time
(override)
When in AUTO mode, you can override the existing temperature setting for a short
period of time.
Press the + or – buttons to change the temperature setting.
While in temperature override the pointer indicates both AUTO and MAN (Fig. 2).
When the next programmed time/temperature event is reached, the device will revert
to the AUTO mode.
5. How to set a constant room temperature (manual operation)
In this mode, a constant temperature can be set, and the pre-set program is ignored.
The temperature last selected is chosen as the initial temperature.
How to activate this mode
Press the < button until the pointer indicates MAN (Fig. 3).
Set the temperature by pressing the +- button
Exit the mode
by pressing the > button
6. How to set the room temperature for a set time
(holiday/party mode)
In this mode, the temperature can be set for periods of time ranging from a few hours
up to 199 days, e.g. when you are away from home for longer periods of time
(holidays).
The remaining hours/days are shown. Time periods between 1 hour and 23 hours and
1 day and 199 days can be set.
How to activate this mode
Press the < button until the pointer indicates the suitcase icon (Fig. 4)
Set the temperature by pressing the +- button
Select the time by pressing the < button
Set the time by pressing the +– button
Once you have set your time period, the time will flash for 10 seconds and then start
the holiday/party period.
To exit this mode, press < or >.
When hours have been set, the controller will return to AUTO mode once the set
hours have passed.
When days have been set, the controller will return to AUTO mode at midnight of the
last day.
Note: the current day (today) must be included in the setting.
e.g. 1 day is set; the controller returns to AUTO today at midnight.
Days
Temperature
see note below
+ or – buttons
for setting
values e. g.
temperature
Pointer indicates
the day of the week
Flame icon
(heating on)
Time
Pointer indicates
the current mode
Modes:
automatic, manual,
holiday, day, program
(see 3., 4., 5., 6.)
Moves the pointer
to the left e. g. to
select the mode
Moves the pointer
to the right e. g. to
select the mode
Setting the clock
(see 11.)
Time / Temperature
Program events 1…6
in sequence morning,
midday and night (see 7.)
Note: Temperature displayed is actual room temperature.
After pressing + or – button the set temperature is displayed. Once adjustment
is complete and after 5 seconds display will show actual room temperature.
Battery run low
(see 10.)
Fig. 1 Fig. 2
Fig. 3 Fig. 4
7. Pre-set programs
There are 3 pre-set time/temperature programs which are already available in the
controller. Pre-set program 1 (as shown below) is the default. Therefore, if pre-set
program 1 is the best program to suit your lifestyle, you do not need to change the
time/temperature settings on the device.
To select an other program see 9.3
Program 1 (home during the day)
Monday to Friday
Events 1 23456
Time 6:00 8:30 12:00 14:00 17:00 22:00
Temperature °C 21,0 18,0 21,0 18,0 21,0 15,0
Saturday and Sunday
Events 1 23456
Time 7:00 10:00 12:00 14:00 17:00 23:00
Temperature °C 21,0 18,0 21,0 21,0 21,0 15,0
Program 2 (home for lunch and on weekends)
Monday to Friday
Events 1 23456
Time 6:00 8:30 12:00 14:00 17:00 22:00
Temperature °C 21,0 18,0 21,0 18,0 21,0 15,0
Saturday and Sunday
Events 1 23456
Time 7:00 10:00 12:00 14:00 17:00 23:00
Temperature °C 21,0 21,0 21,0 21,0 21,0 15,0
Program 3 (at work all day)
Monday to Friday
Events 1 23456
Time 6:00 8:30 12:00 14:00 17:00 22:00
Temperature °C 21,0 18,0 18,0 18,0 21,0 15,0
Saturday and Sunday
Events 1 23456
Time 7:00 10:00 12:00 14:00 17:00 23:00
Temperature °C 21,0 18,0 21,0 21,0 21,0 15,0
8. How to adjust the pre-set time/temperature program to suit
personal needs
Select the day function by pressing the > button up to position "Day"
Select the day by pressing the +- button
Set the times for this day
Select the event (1…6) by pressing the > button
Set the time by pressing the +- button
Select the temperature by pressing the > button
Set the temperature by pressing the +- button
The > button must be pressed to accept a setting.
If you wish to change other events or days, repeat the actions described above. To
return to the auto mode, press the < button.
Note: The last event of the current day can be extended up to the first event of the
following day.
6:00 h 8:00 h 10:00 h 12:00 h 14:00 h 16:00 h 18:00 h 20:00 h 22:00 h
°C
22
21
20
19
18
17
16
15
14
Mon – Fri
Sat – Sun
6:00 h 8:00 h 10:00 h 12:00 h 14:00 h 16:00 h 18:00 h 20:00 h 22:00 h
°C
22
21
20
19
18
17
16
15
14
Mon – Fri
Sat – Sun
6:00 h 8:00 h 10:00 h 12:00 h 14:00 h 16:00 h 18:00 h 20:00 h 22:00 h
°C
22
21
20
19
18
17
16
15
14
Mon – Fri
Sat – Sun
Table 1 User options
User
options Description Select between Default
1 Change 12 h or 24 h clock 12 24 24
2 Change he manual set point temperature 7 32 20
3 Change to another pre-set program 1 3 1
4 Change the number of program events per day 2, 4 or 6 6
5 Switch on/off automatic daylight savings time/standard time change ON OFF ON
6 Change temperature display –5.0 5.0 0.0
7 Restore the built in time temperature programs ON OFF OFF
8 Switch off the thermostat ON OFF OFF
Pay attention to correct
polarity of the batteries!
If operating mode "7 days" is chosen (see installer options, option 1), the days can be
selected as blocks or individual days (Fig. 5 to 8).
The blocks are selected by repeatedly pressing the > button.
Note: To facilitate programming, blocks of days with the same times/temperatures can
be formed before starting.
Fig. 5: Fig. 6:
Monday to Friday as one block Saturday and Sunday as one block
(working days) (days off)
Fig. 7: Fig 8:
Each day is individual day Monday to Sunday as one block (all days)
9. How to change user options
The controller offers a number of options that can be changed by the user (see Table 1.).
To activate the menu, in AUTO Mode press the < and > buttons simultaneously
for 3 seconds
elect an option by pressing the < or > button
Change an option by pressing the +- button
Press < or > to accept each change.
To exit the menu, press the < and > buttons simultaneously for 3 seconds.
If no button is pressed within 2 minutes, the device will return to the auto mode.
9.1 How to change from 24h to 12h clock (option 1, table 1)
Shows the time as 24 hours or 12 hours
9.2 How to change the manual set point temperature (option 2, table 1)
Setting the temperature used when the manual mode is selected for the first time, e.g. 20°C
9.3 How to change to another pre-set program (option 3, table 1)
Selection of a pre-set program to be used for programming events (see 7.).
9.4 How to change the number of events per day (option 4, table 1)
2, 4 or 6 time/temperature events can be selected for all days according to individual
need (not used events will be skipped). If there is no need for e.g. 6 events, choosing
4 makes programming easier.
9.5 How to switch on/off the automatic daylight savings time/standard time
change (option 5, table 1)
You can select whether or not you want the time change to be carried out
automatically. If it is not carried out automatically, the time has to be adjusted
manually (see 11.).
9.6 How to change the temperature display (option 6, table 1)
The temperature display can be adjusted to individual needs, e.g. 3 = +0,3°; -15 = -1,5°.
9.7 How to restore the built in time temperature programs (option 7, table 1)
Restores the pre-set programs to its original factory settings.
9.8 How to switch off the programmable thermostat (option 8, table 1)
When switched off, the programmable thermostat no longer controls the room
temperature and the room is not heated. The display will show OFF, and the buttons
will not function.
In the installer options (refer to Installation Guide) you can select whether or not frost
protection is to active (heating is called for if the temperature falls below 5°C) when
the programmable thermostat is switched off.
10. How to change the batteries
When the batteries start to run low, the battery icon (refer to Fig. 1) starts to blink.
The controller continues to function normally.
After roughly 6 months, the device will cease to function and will permanently display
the battery icon (Fig. 9).
Disposal of batteries according to legislation.
Fig. 9
11. How to change the time, day, month and year
The controller comes with a pre-set clock, which also automatically switches from day-
light savings time to standard time.
There should be no need to change these settings. However, should the need arise, the
settings can be changed in the following way.
Activate the clock mode:
Select DAY with button > and then Sunday with button +
With button > move through all 6 time/temperature events (without any modifiaction)
until the pointer indicates the clock icon.
The time will now flash.
Set the time by pressing the +- button
Press the > button to select the day Press the +- button to change the setting
Press the > button to select the month Press the +- button to change the setting
Press the > button to select the year Press the +- button to change the setting
Press the > button to return to the AUTO mode
3114 Instat+2R (GB) 06.03.2006 10:07 Uhr Seite 1
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EBERLE Instat+ 2R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EBERLE Instat+ 2R in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EBERLE Instat+ 2R

EBERLE Instat+ 2R User Manual - Dutch - 2 pages

EBERLE Instat+ 2R User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info