703715

Easymaxx LS520B-RGB-2M - Z05887 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
EN Instructions
Customer Service / Importer:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
✆ +49 38851 314650 *)
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
All rights reserved.
Remote control
1 On/Off switch
2 White light (mixed colour)
3 Flash (fl ashing function)
4 Strobe (slow fading out of
a colour)
5 Fade (slow fading out with
colour change)
6 Smooth (smooth colour
change)
7 Control panel for colour
selection (12 mixed co-
lours)
8 RGB setting (red, green,
blue)
9 Increase/decrease the in-
tensity of colour
Start-up
PLEASE NOTE
■ First connect the LED strips and the connector cables with one
another before you plug the product into a device that is con-
nected with the mains supply.
1. Connecting the cables – Connect the LED strips with each
other or use the connector cables. To do so, connect them
in the following order: LED strip with USB plug → connector
cable → connection piece → LED strip → connector cable etc.
Make sure that all LED strips are similarly aligned (all arrows
are pointing in the same direction). Otherwise the circuit will not
be closed.
2. Cleaning the surfaces – In order for the LED strips to stick in
place, the surface they are stuck to must be smooth, dry and
free of dust, grease and dirt.
3. Sticking the LED strips in place – ATTENTION! When sti-
cking the LED strips in place, they may not be connected
to the mains supply!
Carefully remove the protective foil of a LED strip and stick it
on the desired area. Follow the same steps for the other LED
strips. Make sure that the USB cable is close enough to the
desired USB port!
4. Connecting to the device – Connect the USB cable to the
USB port of the desired device (television or similar).
The backlight is now ready for operation.
Changing the remote control battery
PLEASE NOTE
■ Before inserting the battey, check whether the contacts in the
article and on the battery are clean, and clean them if neces-
sary.
The battery for the remote control has already been inser-
ted. You only have to remove the transport guard.
1. The battery compartment is lo-
cated on the narrow side of the
remote control. Pull it out as
shown.
2. Remove the empty battery
and insert a 3 V battery, type
CR2025. The positive terminal
must point upwards.
3. Place the battery compartment back in the remote control so
that it locks in place.
Use
1. Turn on the LED backlight by pushing the ON button on the
remote control.
2. Select the desired colour or the desired effect and push the
corresponding button on the remote control.
Please note that the colour settings are mixed colours. For
this reason, the colour tints may exhibit minor deviations.
Even white light is a mixed colour and thus not a purely
white colour tint!
3. Set the desired colour brightness using the buttons to increa-
se/decrease the intensity of colour.
4. Push the OFF button to turn off the LED backlight.
Troubleshooting
If the device does not work properly, check whether you are able to
rectify the problem yourself. If the problem cannot be solved with
the steps that are listed, contact the customer service department.
Do not attempt to repair a defective electrical device
yourself!
If the light does not switch on, check
• whether all cables are properly connected with one another.
• whether all LED strips are properly aligned (all arrows are poin-
ting in one direction).
• whether the connected device is properly connected with the
socket.
• whether the socket is defective. Try another socket.
• the fuse for your mains connection.
• whether the battery in the remote control is empty.
Technical data
Product number: 05887
Model number: LS520B-RGB-2M
Voltage supply:
LED strips (USB): 5 V
Remote control: 3 V (1 x 3 V battery,
type CR2025)
Output: 2.5 W
Disposal
Dispose of the packaging material in an environmentally
friendly manner and take it to a recycling centre.
Dispose of the device in an environmentally friendly man-
ner at a recycling centre for used electrical and electronic
devices. More information is available from your local au-
thorities.
Batteries should not be disposed of in the normal household
waste. They should be removed prior to disposal of the de-
vice and disposed of separately from the device at suitable
collection points.
Illustration similar
1
2
3
4
5
6
9
8
7
push
pull
Z 05887 M DS V3 0318
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Easymaxx LS520B-RGB-2M - Z05887 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Easymaxx LS520B-RGB-2M - Z05887 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info