761234
5
Zoom out
Zoom in
Previous page
1/252
Next page
5
Looking after your
hand dryer
Please register as a Dyson
hand dryer owner
To help us ensure you receive a prompt and
efficient service, please register your machine
at www.dyson.com/airblade. This will
register your guarantee, confirm ownership
of your Dyson machine in the event of an
insurance loss, and enable us to contact you
if necessary.
You will need your serial number, which can
be found on the rating plate inside the main
body and on the information sticker on the
front of the machine.
Please ensure all instructions and guidance in
the Installation instructions and Maintenance
manual are adhered to or your guarantee
may be invalidated.
Maintenance
How to use
Place your hands beneath the Dyson
Airblade™ hand dryer arms and it will start
automatically, creating sheets of air that
scrape water from your hands.
For best dry time results:
Keep your hands flat and parallel to the
machine's surface, approximately 5mm from
the air aperture, drawing your hands through
the airflow from your wrists to finger tips.
Move your hands slowly through the airflow,
keeping a consistent speed (approx.
2.5 seconds per side), alternating between
front and back each time.
Keep your hands flat, close the gaps between
your fingers and keep your thumbs tucked in,
so the whole of your hand is drawn through
the airflow.
For more information about the power
modes, go to www.dyson.com/airblade
Troubleshooting
Hand dryer cuts out
After 30 seconds of continued use the hand
dryer will turn off automatically. Remove and
replace hands to restart.
Turn the machine off and on again at the
mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of
dust and blockages. If the air apertures are
dusty, simply remove dust.
Check that the air inlet is free from blockages.
Dry time has increased
Make sure that the correct power mode has
been selected.
Check that the air inlet is free from blockages.
Inspect the air apertures for dust,
and remove.
Airflow is running hotter
than usual
Check that the air inlet is free from blockages.
Inspect the air apertures for dust,
and remove.
Air is continuously running
After 30 seconds of continued use the hand
dryer will turn off automatically. Remove and
replace hands to restart.
Check that the air inlet is free from blockages.
Inspect the air apertures for dust,
and remove.
Contact Dyson for further support
and information or online at
www.dyson.com/airblade
Cleaning
The hand dryer should be cleaned daily.
Wipe the sensors using a soft cloth and non-
abrasive cleaner.
Important information
Don't pressure wash the machine.
All cleaning chemicals should be used
exactly as indicated by the manufacturers
instructions (including appropriate dilution).
Any chemicals intended for use should first be
tested on an inconspicuous area to confirm
suitability. Aside from cleaning chemicals,
care should be taken to avoid any harmful
fluids from coming into contact with the
machine, in particular oils and alcohol-
based products.
Filter maintenance
Regularly check the air inlet to ensure that it is
free from dust and debris. Simply wiping the
inlet with a soft cloth should be sufficient to
remove dust and debris.
If the air inlet gets clogged, further cleaning
or a filter change might be required.
If required for high usage environments, a
Dyson filter change kit provides everything
needed to change your machine’s HEPA
filter on site. Contact the Dyson Helpline for
more information.
Filter cleaning or replacement for your hand
dryer can be carried out by carefully following
the instructions given in the filter change kit. If
in any doubt, consult a qualified electrician or
contact the Dyson Helpline for support.
Servicing
If your hand dryer needs servicing, please
call the Dyson Helpline or visit the website at
www.dyson.com/airblade
07.08.2019 10:12 - C101785-HU03_OPMAN_GLOB_X280-1A-OPMAN-TEXT-101785_15_4c0s
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dyson Airblade 9kJ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dyson Airblade 9kJ in the language / languages: All languages as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dyson Airblade 9kJ

Dyson Airblade 9kJ Additional guide - English - 1 pages

Dyson Airblade 9kJ Additional guide - All languages - 2 pages

Dyson Airblade 9kJ Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info