633975
160
Zoom out
Zoom in
Previous page
1/161
Next page
Fehlermeldungen/Betriebsanzeigen Beisler 100-68
Error massages/Operation display Beisler 100-68
Für DAC3 Programm-Version V0.50, Datum 21.05.07
For DAC3 program-version VO.50, Datum 21.05.07
fehler100-68dac3.doc Page 11 / 12
Sensor Klammer vorn (S5) nicht erreicht
Einstellung Sensor Klammer vorn korrigieren
(mechanische Kollision; Schalter prüfen)
Error 9710
Limit switch for feed clamp active
Check material feed and limit switch S101
Fehler bei der Pattenabtastung mit Lichtschranke
Reflexfolie kontrollieren; Ausrichtung der
Lichtschranken prüfen
Info 9720
Error at the light barrier for flap scanning
Check the reflecting foil; check the alignment of the
light barriers
Patte wurde vor dem vorderen Anlegepunkt angelegt
Patte korrekt einlegen
Info 9721
Flap has been positioned in front of the front
positioning point
Position the flap correctly
Patte liegt über den maximalen Nähbereich hinaus
(hinter dem hinteren Anlegepunkt)
Pattengröße kontrollieren; Patte korrekt einlegen
Info 9722
Flap protrudes from the maximum sewing area (behind
the rear positioning point)
Check the flap size; position the flap correctly
Flusen am Pattenanfang
Patten mit glatten Kanten einlegen; Reflexfolie
kontrollieren
Info 9723
Fluff at the flap beginning
Feed flaps with smooth edges; check the reflecting
foil
Patte zu groß oder Reflexfolie verschmutzt bzw. defekt
Pattengröße und Reflexfolie kontrollieren
Info 9726
Flap too large or reflecting foil dirty or faulty
Check the flap size and reflecting foil
Anhaltestrecke für die Pattenschräge nicht
ausreichend
Einschubgeschwindigkeit verringern
Info 9727
Stop section insufficient fort he flap angle
Reduce the slide-in speed
Mittelmesser nicht betriebsbereit
Kabel überprüfen
Info 9800
Center knife not ready for use
Check cable
Ausroller nicht betriebsbereit
Kabel überprüfen
Info 9810
Smoother not ready for use
Check cable
Defekte Maschinenparameter (Checksummenfehler)
Maschinenparameter neu initialisieren (Service);
Maschinenparameter einstellen oder vom USB-
Stick einlesen
Error 9900
Defective machine parameters
(Checksum error)
Re-initialize machine parameters (test program);
Set machine parameters or read them from the
dongle
Defekte Taschenfolgen (Checksummenfehler)
Taschenfolgen neu initialisieren (Service);
Taschenfolgen einstellen oder vom USB-Stick
einlesen
Error 9901
Defective pocket sequences
(Checksum error)
Re-initialize pocket sequences (test program);
Set pocket sequences or read them from the dongle
160


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 100-68 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 100-68 in the language / languages: German as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 100-68

Durkopp Adler 100-68 User Manual - English - 162 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info