Manual Dremel Trio (page 10 of 80) (English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish)

488596

Zoom out

Zoom in

1/80

g. Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

SERVICE

a. Have your power tool serviced by the manufacturer or its

authorised agent in order to avoid a safety hazard using

only identical replacement parts. This will ensure that the

safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

SAFETY WARNINGS COMMON FOR GRINDING,

SANDING, WIRE BRUSHING, POLISHING OR

ABRASIVE CUTTING-OFF OPERATIONS

a. This power tool is intended to function as a grinder

or sander. Read all safety warnings, instructions,

illustrations and speciﬁcations provided with this power

tool. Failure to follow all instructions listed below may result

in electric shock, ﬁre and/or serious injury.

b. Operations such as wire brushing, polishing or cutting-

off are not recommended to be performed with this

power tool. Operations for which the power tool was not

designed may create a hazard and cause personal injury.

c. Do not use accessories which are not speciﬁcally

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

d. The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can break

and fly apart.

e. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

f. The arbour size of wheels, ﬂanges, backing pads or

any other accessory must properly ﬁt the spindle of the

power tool. Accessories with arbour holes that do not match

the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of control.

g. Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing

anaccessory, position yourself and bystanders away from

the plane of the rotating accessory and run the power

tool at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test time.

h. Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or work piece fragments. The

eye protection must be capable of stopping flying debris

generated by various operations. The dust mask or respirator

must be capable of filtrating particles generated by your

operation. Prolonged exposure to high intensity noise may

cause hearing loss.

i. Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of work piece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

j. Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

A cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and shock the

operator.

k. Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your hand

or arm may be pulled into the spinning accessory.

l. Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab

the surface and pull the power tool out of your control.

m. Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

n. Regularly clean the power tool's air vents. The motor's

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

o. Do not operate the power tool near ﬂammable materials.

Sparks could ignite these materials.

p. Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or

shock.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of the

binding. For example, if an abrasive wheel is snagged or pinched

by the work piece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing the

wheel to climb out or kick out. The wheel may either jump toward

or away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under these conditions. Kickback is the result of power tool

misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below.

a. Maintain a ﬁrm grip on the power tool and position your

body and arm to allow you to resist kickback forces.

Always use auxiliary handle, if provided, for maximum

control over kickback or torque reaction during start-up.

The operator can control torque reactions or kickback forces,

if proper precautions are taken.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dremel Trio in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dremel Trio Manual

Product: