768197
31
Zoom out
Zoom in
Previous page
1/40
Next page
8.0 MAINTENANCE
R699763 - Dream E User Manual 31
8.0 MAINTENANCE
8.1 Clean Dirt on the Cabinet
Always use a soft cloth. In case of heavy soiling, soak a cloth in neutral detergent diluted with water, wring dry and
wipe, followed by wiping again using a dry cloth.
Caution
Pay attention to the following as the cabinet may deteriorate in condition, get damaged or paint may come
off.
Do not wipe with a stiff cloth.
Do not wipe with force.
Do not wipe with thinner or benzene.
Do not spray volatile chemicals like insecticide.
Do not allow prolonged contact with rubber or plastic products.
8.2 Dirt on the Lens
The lens shall be cleaned using commercial blowers or lens cleaning papers (for cleaning glasses and cameras).
Do not use fluid-type cleaning agents. This may lead to peeling of the surface coating film. The lens surface is
fragile. Avoid rubbing it hard or knocking.
8.3 Replacing the Lamp
Light-source Lamp and Lamp Usage Time
The life of light-source lamps used for this unit is about 2000 hours.
The lamp life of 2000 hours is merely the average life span of light-source lamps and we do not provide any
guarantee for this figure. The lamp life may not reach 2000 hours depending on the operating conditions.
Deterioration progresses rapidly when the remaining lamp usage time is short. Get ready or replace with a new
lamp when the accumulated usage time exceeds 1700 hours. Depending on the operating conditions, the lamp
may have to be exchanged earlier.
If the image is dark or color tone abnormal, replace the lamp as soon as possible.
•You can also check the accumulated hours of usage. Please refer to Lamp Time of the Information menu.
When the lamp usage time reaches 1700 hours
The Lamp replacement message will be displayed on the screen the next three projection starts.
Press the [ESC] button to clear the display.
Procedure for Lamp Replacement
During the lamp replacement process, you may have access to sensitive parts of the projector.
Loosen the 2 screws on the lamp trap.
Open the lamp Cover, at the rear of the projector and pull it upwards.
Loosen the 2 screws on the lamp unit and lift up the handle.
Pull out the lamp unit.
Insert the new lamp unit until it is fully in.
ABOUT LAMP REPLACEMENT
If this unit is installed in a constricted place, attempting to replace the lamp in that place may cause injury. Move this
unit to a place large enough to perform work.
Use only genuine replacement parts for the lamp unit. Otherwise, malfunction may occur. Also, never attempt to re-
use an old lamp unit. This may cause marked performance deterioration or lamp blowout, thus leading to unit
malfunction. Broken pieces of the lamp outside this unit may also cause injuries during lamp unit exchange.
Do not replace the lamp immediately after this unit has been used. The temperature of the lamp is still high and this
may cause a burn. Allow a cooling period of 1 hour or more before replacement.
Before replacing the lamp unit, pull out the power plug from the outlet while the [POWER] Led is still light red.
Replacing a lamp with the plug connected to the outlet may cause injuries or electric shocks.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DreamVision Dream E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DreamVision Dream E in the language / languages: English as an attachment in your email.

The manual is 5,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info