629513
3
Zoom out
Zoom in
Previous page
1/24
Next page
Elite Control Operations Manual Read This Manual Before Proceeding
L-2230 ENGLISH 1
INTRODUCTION
The Elite Control is a microcontroller-based unit designed for use with direct expansion, reverse-cycle air conditioning systems.
READ THIS MANUAL BEFORE PROCEEDING
Read this manual completely before you proceed with the installation and operation of the Elite. If you have questions or require
assistance with your Elite control, contact the Dometic Marine Service Department at +1 954-973-2477.
The Elite is covered under existing Marine Air Systems Warranty Policy. Incorrect installation, neglect and system abuse are not
covered under Marine Air Systems warranty policy.
FEATURES
STANDARD
User-friendly five-button display panel requires no manual for basic operation.
Five-volt logic and microcontroller located in the display.
Three-digit, seven-segment display panel indicates degrees Fahrenheit or degrees Celsius.
Automatic and three programmable manual fan speeds.
22 programmable parameters for custom installations.
High- and low-refrigerant-pressure sensor inputs.
Moisture Mode for controlling relative humidity.
De-Icing cycle to prevent evaporator coil icing.
Programmable compressor staging delays.
Universal 115/230 volt, 50/60 Hz AC power supply.
Nonvolatile memory retains settings without batteries.
Programmable display-brightness control.
Programmable failsafe modes.
Fits Vimar® switch bezels.
OPTIONAL
Outside air temperature sensor.
Alternate air temperature sensor.
Pump Sentry water sensor.
Electric heating control capabilities.
CAN-bus network capability (available in software revision A16 or newer).
Air Filter Cleaning or Replacement Timer (available in software revision A15 or newer).
Low-Voltage Monitor (available in software revision A15 or newer).
This manual provides all necessary information for proper installation and operation of the Elite. Poor installation and
misunderstood operating parameters will result in unsatisfactory performance and possible failure.
DESCRIPTION OF CONTROL
See Figure 1 and Table 1 on page 2 to identify all parts of the control.
POWER
Press the Power Button once to engage the system. The display is blank when the system is off and indicates current room
temperature when the system is on.
MODE SELECTION
Press and release the Mode Button until the desired Mode LED is illuminated.
SET POINT
Press the Up or Down button to set the desired room temperature. To view the set point, momentarily press and release the Up
or Down button.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dometic Elite Control DX systems at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dometic Elite Control DX systems in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info