66431
2
Zoom out
Zoom in
Previous page
1/16
Next page
All models include
RCA inputs
High Level input
Continuos variable low pass and/or high
pass crossover
Bass boost feature (only on CA23 & CA41)
Remote turn on / off
Automatic remote turn on/ off on high level
input without connecting any remote wire
Electronic protection circuitry against
short-circuit, DC offset and thermal overload.
Bridgeable design to direct full power to
one or two subwoofers etc.
Installation
Before you begin installation
Before you begin you need to read the manual, to have
some tools, cables and other material available. There
is one such list of material on the following page.
Amplifier location
Important
Allow air circulation around the amplifier.
2
Disconnect Battery
Before starting the instal-
lation, always disconnect
the negative terminal of
the battery.
The DLS Performance series of amplifiers have a
compact design that allows great flexibility in
mounting. You can mount it under a seat or in the
trunk.
When you select a location, do remember that the
amplifier generates a lot of heat.
Choose a location where air can circulate freely
around the amplifier. Do not cover the amplifier
with carpets or hide behind trim panels.
Do not mount the amplifier in an inverted or upside
down position.
Check all locations and placements carefully
before making any cuts, drilling any holes or ma-
king any connections.
This is the best way to
mount the amplifier to get
the best cooling.
CA22, 23, 31, 41 & 51
CA22
2 x 60 Watt RMS / 2 x 100 Watt max in 2 ohm
1x 200 Watt RMS bridged
CA23
2 x 135 Watt RMS / 2 x 200 Watt max in 2 ohm
1 x 400 Watt RMS bridged
CA31
2 x 65 Watt RMS / 2 x 90 Watt max in 2 ohm
1 x 170 Watt RMS bridged
1 x 170 W RMS on sub channel
CA41
4 x 70 Watt RMS / 4 x 125 Watt max in 2 ohm
2 x 200 Watt RMS bridged
CA51
4 x 50 Watt RMS / 4 x 80 Watt max in 2 ohm
2 x 150 Watt RMS bridged
1 x 170 Watt RMS on sub channel
All above RMS power ratings with 4 ohm load
at 13,8 Volt DC.
DLS logo on amplifier cooling flange
The DLS logo on top of the amplifier is attached
with two 1 mm hex. screws. The logo can be remo-
ved and twisted 90 or 180 degrees, and then
screwed back in wanted position. The logo can be
mounted in four different ways to match your in-
stallation.
Removal of side flanges
In order to fasten the amplifier to the surface and
connect speaker and power cables, the flanges on
the sides must be removed. This is done by
loosening the hex screws on top of the amplifier.
Use a 3 mm hex key.
Remove these
screws using a 3
mm hex. key for
removal of side
flange. Remount
after fastening the
amplifier and
connection of the
speaker and power
cables.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS CA41 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS CA41 in the language / languages: English as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info