594201
32
Zoom out
Zoom in
Previous page
1/71
Next page
©2015 DJI. All Rights Reserved. 32 |
7.
8.
9.
10.
11.
Wait until the LED flight indicator starts to slowly blink green/yellow. This means the aircraft is initializing
and entering the Ready to Fly/Ready to Fly (non-GPS) state. Then proceed to execute the CSC
command to start motors.
Push the throttle stick up slowly to lift the aircraft off the ground. Refer to the Remote Controller
Operation (Page 10) for more details.
Enjoy your flight while capturing and recording with the DJI VISION App. Refer to the Using DJI VISION
App (Page 42) for more details.
Pull down the throttle stick to descend. The stick will lock into place and the aircraft will descend steadily.
After landing the aircraft on the ground, keep the throttle stick at its lowest position for about 3 to 5
seconds which will automatically stop the motors.
You SHOULD NOT execute the CSC during normal flight! This will stop the motors and cause the
aircraft to descend rapidly and drop without any type of control.
(1)
(2)
(3)
(4)
When the LED flight indicator blinks yellow rapidly during flight, the aircraft has entered into
Failsafe mode, refer to the Failsafe Function (Page 32) for details.
A low battery capacity warning is indicated by the LED flight indicator blinking red slowly or
rapidly during flight. Refer to the Low Battery Level Warning Function (Page 34) for details.
Watch the quick start video about flight for more flight information.
Aircraft and battery performance is subject to environmental factors such as air density and
temperature. Be very careful when flying 3000 meters (9800 feet) or more above sea level, as
battery and aircraft performance may be reduced.
11.4 Failsafe Function
The aircraft will enter Failsafe mode when the connection from the remote controller is lost. The flight control
system will automatically control the aircraft to return to home and land to reduce injuries or damage. The
following situations would make the aircraft fail to receive a signal from the remote controller and enter Failsafe
mode:
(1) The remote controller is powered off.
(2) The aircraft has flown out of the effective communication range of the remote controller.
(3) There is an obstacle obstructing the signal between the remote controller and the aircraft, essentially
reducing the distance the signal can travel.
(4) There is interference causing a signal problem with the remote controller.
Failsafe works differently depending on the mode the aircraft is in when Failsafe mode is initiated whether it is in
the Ready to Fly or Ready to Fly (non-GPS) mode.
Ready to Fly (non-GPS) ---- Automatic landing
The flight control system will try to keep the aircraft level during descent and landing. Note that the aircraft may
be drifting during descent and landing process.
32

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DJI Phantom 2 Vision at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DJI Phantom 2 Vision in the language / languages: English as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DJI Phantom 2 Vision

DJI Phantom 2 Vision User Manual - German - 63 pages

DJI Phantom 2 Vision User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info