Manual Dimplex Cadiz ROF2ECC (page 6 of 8) (English)

798039

Zoom out

Zoom in

1/8

Electronic Climate Control - see Fig. 5

(ROF2ECC & ROF3ECC models only)

Operation

The electronic control allows MANUAL and AUTO operation. In manual

on mode there are three heat settings LOW, MEDIUM and HIGH. In

AUTO mode the heater comes on as per the programmed timer settings

(See Setting programs). At any point if the heater is active i.e. heat is

being produced, the ‘ ’ neon is lit - see Fig. 5.

Initial Operation

When the heater is connected to the mains the ‘ ’ neon will be lit and

the display is blank. Press the ‘ ’ button and the display goes to full

heat set to 35oC - see Fig. 13.

Note: All display characters are displayed in Fig. 18.

Standby Mode

With the heater ON if the ‘ ’ button is pressed, the heater will go into

standby mode, heater switches off, the display goes blank and only the

MAINS ON neon ( ) remains lit. On pressing the ‘ ’ button again the

heater will come on in the mode and with the settings it had prior to

going into standby mode.

Setting Time

To set the time press ‘P’ and the ‘ ’ appears with the digits flashing -

see Fig. 14.

1. Press the ‘ ’ or ‘ ’ until the correct time is displayed.

2. Press ENTER. The display will return to the state prior to entering

set time.

N.B. If no keys are pressed after 4 minutes the display will revert to the

state prior to entering set time.

Manual Operation

Pressing ‘ ’ from the default HIGH screen (Fig. 13) brings the heater

into AUTO mode - see ‘Setting the Timer Programs’. Press again to put

the heater into OFF mode. Press again for LOW heat (Fig. 12). Press

again for MEDIUM heat. Press again brings the user full circle to HIGH

heating mode.

Setting the Desired Temperature

The desired temperature can be set using the ‘ ’ or ‘ ’ keys. The

temperature can be set from 5oC to 35oC and this will be shown on the

display. When the temperature is reached the heater will automatically

switch OFF. If the ambient temperature drops the heater will come on

again automatically. Note the switch OFF and ON is a staged switching,

to conserve energy and assist with temperature regulation e.g. if the

heater is set to HIGH heat and the temperature is set to 28oC, at 26oC

the heater will switch to MEDIUM heat, at 27oC the heater will switch

to LOW heat. Then at 28oC the heater will switch OFF completely.

Setting the Timer Programs

Two program settings are possible, P1 and P2. Only HIGH heat is

possible for program settings. Press ‘ ’ twice, P1 AUTO ON and a time

will flash - see Fig. 15. The first P1 ON time can now be set:

1. Press the ‘ ’ or ‘ ’ buttons to set the time.

2. Press ‘ ’.

Now P1 AUTO off is displayed, P1 OFF time can now be set:

3. Press the ‘ ’ or ‘ ’ buttons to set the time.

At this point either :

(a) press ‘ ’ to exit the Program mode and return to

AUTO mode. The heater is now in AUTO mode. The heater will

switch ON and OFF depending on programme P1 previously

entered.

(b) press ENTER to set the ON and OFF times for program

2, as in steps 1 to 3 above.

At this point press ENTER or PROG to exit the Programme mode. The

heater is now in AUTO mode. The heater will switch ON and OFF

depending on programme P1 & P2 previously entered. If after

programming and returning to the AUTO mode display, P1 or P2 is

active, the display will show PROG 1 AUTO ON or PROG 2 AUTO ON

depending on which is active - see Fig. 16. An OFF time cannot be

entered which is less than the corresponding ON time. When setting

the timer programs if no keys are pressed, the display will (after 4

minutes) revert to the previous display i.e. display prior to entering

Program mode.

Run Programs

If MODE is pressed until AUTO appears on the screen (either AUTO-

ON or AUTO-OFF), the heater will run both P1 and P2 program as they

are set.

NOTE: The heater cannot be programmed to run P1 only or P2

only.

To cancel P1, set P1 OFF time to be same as P1 ON time. To cancel P2

set P2 OFF time to be same as P2 ON time.

Review Program settings

To review the program settings the heater must be in AUTO mode.

Press ENTER and the times for PROG 1 ON, PROG 1 OFF, PROG 2

ON and PROG 2 OFF will be displayed consecutively for 2 seconds.

The display will automatically return to the state it was in before ENTER

was pressed.

FROST Protection Mode

With the heater in any mode, OFF, MANUAL ON or AUTO, if the

displayed set temperature is reduced to 5oC the heater will go into FROST

Protection mode - see Fig. 17. In this mode only, if the ambient

temperature drops below 5oC, will the heater come on. This is to prevent

freezing. In FROST Protection mode the heater comes on in the high

heat mode only. Pressing the ‘ ’ button is the only way to bring the

heater out of this special mode.

Remote Control Operation - see Fig. 19

The batteries for the remote control are not installed in the remote but

are packed separately in the carton. To install batteries please follow

diagrams behind battery cover on the remote control.

The remote allows the set temperature to be adjusted, the mode to be

selected or can be used to put the heater in FROST Protection mode.

Press the ‘ ’ button on the Remote Control to go from OFF, Man On

High and back to OFF again. Press the ‘ ’ or ‘ ’ buttons on the remote

to set desired temperature between 5oC and 35oC. Press the ‘’ button

to put the heater into FROST Protection mode. Pressing the ‘ ’ button

(on the Remote Control) is the only way (using the Remote Control) to

bring the heater out of this mode i.e. pressing the ‘ ’ or ‘ ’ buttons on

the remote will have no effect on the heater.

Discard leaking batteries

Dispose of batteries in the proper manner according to Provincial and

local regulations. Any battery may leak electrolyte if mixed with a different

battery type, if inserted incorrectly, if all the batteries are not replaced at

the same time, if disposed of in a fire or if an attempt is made to charge

a battery not intended to be recharged.

Storage

If the radiator is not required for long periods, for example during the

summer, it should be stored in a dry place and preferably covered to

prevent the accumulation of dirt and dust. The supply cable can be

stored in the cable storage area provided - see Fig. 20. The supply

cord should be neatly coiled around the hooks provided ensuring that

the plug does not trail on the floor. The plug will not fit into this

compartment.

IMPORTANT

The heater must be kept plugged in at the mains to retain the time and

the programmed settings. If unplugged from the mains, resetting the

time and the programmed settings will be necessary.

Safety in Use

This appliance incorporates a number of safety devices. In addition to

the ‘Important Safety Advice’ section, your attention is drawn to the

following;

Tilt Switch

The tilt switch will prevent the heater from working if it is accidentally

tipped over on its side.

If the radiator is tipped over while it is hot, disconnect the power and

allow it to cool, then stand the radiator back upright. Reconnect the

power - normal operation should be resumed. If the radiator does not

heat up again, it is possible that the thermal safety cut-out has operated

- see below.

Safety Overheat Protection

The heater is fitted with a thermal safety cut-out which will switch off the

heater should it overheat for any reason. If the cut-out

operates it is the result of abnormal overheating, and the Customer

Services Helpline should be contacted for further advice.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Cadiz ROF2ECC in the language / languages: English as an attachment in your email.

The manual is 5.49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex Cadiz ROF2ECC

Dimplex Cadiz ROF2ECC User Manual - Dutch - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex Cadiz ROF2ECC Manual

Product: