798031

Dimplex Cadiz Eco CDE2T Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
ELECTRONIC CLIMATE CONTROL
see Fig. 4
(CDE2ECC & CDE3ECC models only)
Operation
The electronic control allows MANUAL and AUTO
operation.
In MANUAL ON mode there are three heat settings:
L/H Side Heat, R/H Side Heat and High Heat
In AUTO mode the heater comes on as per the programmed
timer settings (see Setting programs). At any point if the
heater is active i.e. heat is being produced, the ‘ ’ neon is
lit - see Fig. 4.
Initial Operation
When the heater is connected to the mains the ‘ ’ neon will
be lit and the display is blank. Press the ‘ ’ button and the
display goes to full heat set to 35oC - see Fig. 8.
Note: All display characters are displayed in Fig. 13.
Standby Mode
With the heater ON if the ‘ ’ button is pressed, the heater
will go into standby mode, heater switches off, the display
goes blank and only the MAINS ON neon ( ) remains lit.
On pressing the ‘ ’ button again the heater will come on
in the mode and with the settings it had prior to going into
standby mode.
Setting Current Time
1. Press and hold ‘ ’ and the clock symbol ‘ ’ appears
on the top left hand side of the screen. The user can
now set the time.
2. The hour digit will now ash. To adjust the hour use the
‘’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘
’.
3. The minute digit will ash. To adjust the minute use the
‘’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘
’. The display will return to the state before
entering set time.
N.B. If no keys are pressed after 4 minutes the display will
revert to the state prior to entering set time.
Manual Operation
Pressing ‘ ’ from the default HIGH screen (Fig. 8) brings
the heater into AUTO mode - see ‘Setting the Timer
Programs’. Press again to put the heater into OFF mode -
see Fig. 6. Press again for left hand side heat ( appears
on LCD display - see Fig. 7). Press again for right hand
side heat ( appears on LCD display). Press again brings
the user full circle to FULL heat mode ( appears
on LCD display).
Setting the Desired Temperature
The desired temperature can be set using the ‘ ’ or ‘
’ keys. The temperature can be set from 5oC to 35oC and
this will be shown on the display. When the temperature
is reached the heater will automatically switch OFF. If the
ambient temperature drops the heater will come on again
automatically. Note the electronic climate control device
conserves energy and assists with temperature regulation
e.g. if the heater is set to HIGH heat and the temperature
is set to 28oC, at 27oC the heater will switch to a lower heat
setting. Then at 28oC the heater will switch off completely.
Setting the Timer Programs
Two program settings are possible, P1 and P2. Only high
heat is possible for program settings. Press ‘ ’ once to set
the programs, starting with P1 AUTO ON – See Fig 10.
1. The hour digit will now ash. To adjust the hour use the
‘’ & ‘ ’ buttons. Conrm the hour digit by pressing ‘
’.
2. The minute digit will now ash. To adjust the minute
use the ‘ ’ & ‘ ’ buttons. Conrm the hour digit by
pressing ‘ ’.
3. Now P1 AUTO OFF is displayed, P1 off time can now
be set. Repeat steps 1 & 2 to set P1 off time.
At this point either:
(a) Press ‘ ’ to exit the Program mode and return
to AUTO mode. The heater is now in AUTO mode.
The heater will switch ON and OFF depending on
programme P1 previously entered.
OR
(b) Repeat steps 1 - 3 as above to set the programme
for P2.
At this point press ENTER or PROG to exit the Programme
mode. The heater is now in AUTO mode. The heater will
switch ON and OFF depending on programme P1 & P2
previously entered. If after programming and returning to
the AUTO mode display, P1 or P2 is active, the display will
show PROG 1 AUTO ON or PROG 2 AUTO ON depending
on which is active - see Fig. 11. An OFF time cannot be
entered which is less than the corresponding ON time.
When setting the timer programs if no keys are pressed, the
display will (after 4 minutes) revert to the previous display
i.e. display prior to entering Program mode.
Run Programs
If MODE is pressed until AUTO appears on the screen
(either AUTO-ON or AUTO-OFF), the heater will run both
P1 and P2 program as they are set.
NOTE: The heater cannot be programmed to run P1
only or P2 only.
To cancel P1, set P1 OFF time to be same as P1 ON time.
To cancel P2 set P2 OFF time to be same as P2 ON time.
Review Program settings
To review the program settings the heater must be in AUTO
mode. Press ENTER and the times for PROG 1 ON, PROG
1 OFF, PROG 2 ON and PROG 2 OFF will be displayed
consecutively for 2 seconds. The display will automatically
return to the state it was in before ENTER was pressed.
FROST Protection Mode
With the heater in any mode, OFF, MANUAL ON or AUTO,
if the displayed set temperature is reduced to 5oC the heater
will go into FROST Protection mode - see Fig. 12. In this
mode only, if the ambient temperature drops below 5oC, will
the heater come on. This is to prevent freezing. In FROST
Protection mode the heater comes on in the high heat mode
only. Pressing the ‘ ’ button is the only way to bring the
heater out of this special mode.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex Cadiz Eco CDE2T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Cadiz Eco CDE2T in the language / languages: English as an attachment in your email.

The manual is 1.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info