585376

Dexford RCT 170 Manual

15
Zoom out
Zoom in
Previous page
1/16
Next page
15
Setting the alarm time
You can programme 2 different alarm times in the radio−controlled clock.
1. Press and hold the Mode button (7) until Alarm 1 or Alarm 2 appears in the display.
2. Press and hold the Mode button (7) for 3 seconds (hour digits flash).
3. Use the Up/Down buttons (6/5) to set the required hour and confirm the selection by pressing the Mode button (7).
4. Use the Up/Down buttons (6/5) to set the required minute.
5. Press the Mode button (7) to confirm the setting and activate the alarm time.
Note! If you do not complete any input for a setting for 30 seconds, the process is cancelled and the clock returns
to the Alarm 1 or Alarm 2 display.
Switching the alarm on/off
1. Press the Alarm button (3) to switch the alarm function settings in the following cycle: Alarm 1 activated, Alarm 2
activated, Alarm 1 and Alarm 2 activated, Alarm 1 and Alarm 2 deactivated.
2. When the alarm time activated is reached and the alarm goes off, press the Light/Snooze button (1) to interrupt the
alarm for approx. 5 minutes before it continues again.
3. Press the Alarm button (3) to switch the alarm off, whereby it is switched off permanently for Alarm 2 or switched off
until the same time the next day for Alarm 1.
Note! If you do not press the Alarm button (3) or Light/Snooze button (1), the alarm is automatically switched off
after 4 minutes.
Setting the foreign time
In addition to setting the local time, you can also set the time of a location abroad and switch the display between the two
times.
1. Press and hold the Up button (6) for 3 seconds when the default display is shown. The foreign time display appears
together with an F".
2. Press and hold the Mode button (7) for 3 seconds (hour digits flash).
3. Use the Up/Down buttons (6/5) to set the required hour and confirm the selection by pressing the Mode button (7).
Note! If you do not complete any input for a setting for 30 seconds, the process is cancelled and the clock returns
to the foreign time display.
4. Press and hold the Up button (6) for 3 seconds when the foreign time display appears. The default display reappears
and the F" disappears. You can switch between default display and foreign time display at any time.
Back−lighting
Press the Light/Snooze button (1) to switch on the back−lighting for 5 seconds.
Changing the time format
Press and hold the Up button (6) when the default display is shown in order to switch between the 24−hour and 12−hour
time format (AM/PM).
Radio signal reception
The clock attempts to synchronise with the DCF signal every hour. You can also initiate reception of the DCF signal
manually by pressing and holding the Temperature button (4) for 3 seconds. The reception indicator (12) appears in the
display during the process.
Possible sources of interference for radio signals
D Domestic household equipment without RFI suppression
D TV sets less than 2 m away
D Machines producing HF stray fields (high frequency)
… 15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dexford RCT 170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dexford RCT 170 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info