The coee is not hot.The cups were not preheated.• Enable the cup warmer (A6), leave the
cups at least 20 minutes to warm up.
• Warm the cups by rinsing them with hot
water (Please note: you can use the hot
water function).
The internal circuits have cooled down
because 2/3 minutes have elapsed
since the last coee was made.
Before making the coee, heat the infuser by
rinsing using the "rinse" function (see section
"8.1 Rinsing").
A low coee temperature is set.
Set a hotter coee temperature (see section
"8.10 Setting the temperature").
The coee is weak or not creamy
enough.
The coee is ground too coarsely. Turn the grinding adjustment dial (A5) one
click anticlockwise towards "1" while the cof-
fee mill is in operation (g. 14). Continue one
click at a time until coee delivery is satisfac-
tory. The eect is only visible after delivering
2 coees (see section "9.5 Adjusting the coee
mill").
The coee is unsuitable. Use pre-ground coee for espresso machines.
The coee is delivered too slowly or a
drop at a time.
The coee is ground too nely. Turn the grinding adjustment dial (A5) one
click clockwise towards "7" while the coee
mill is in operation (g. 14). Continue one click
at a time until coee delivery is satisfactory.
The eect is only visible after delivering 2
coees (see section "9.5 Adjusting the coee
mill").
Coee does not come out of one or
both of the spouts.
The coee spouts (A7) are blocked. Clean the spouts with a toothpick (see section
"12.7 Cleaning the coee spouts").
The appliance does not come onThe power cord (C8) connector is not
inserted correctly.
Insert the connector as far as it will go in the
socket at the back of the appliance (A19- g.
1).
It is not plugged into the mains socket. Plug into the mains socket (g. 1).
The main switch (A20) is not turned on.Press the main switch (g. 2).
The infuser cannot be extractedThe appliance has not been turned o
correctly
Turn the appliance o by pressing the but-
ton (B1) (section "7. Turning o").
19. TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
INSERT MILK CONTAINERThe milk container (D) is not inserted correctly.Insert the milk container (g. 24) as far as it
will go.
The milk does not
come out of the milk
spout (D5)
The milk container lid (D2) is dirty.Clean the milk container lid as described in sec-
tion "12.10 Cleaning the milk container"
The milk contains
large bubbles and
squirts out of the
milk spout (D5) or
there is little froth
The milk is not cold enough or is not
semi-skimmed.
Use skimmed or semi-skimmed milk at refrige-
rator temperature (about 5° C). If the result is
not as you wished, try changing brand of milk.
The froth adjustment dial (D1) is incor-
rectly adjusted.
Adjust following the instructions in section "10.
Making cappuccinos and milk-based coees".
The milk container lid (D2) or froth
adjustment dial (D1) are dirty.
Clean the milk container lid and dial as de-
scribed in section "12.10 Cleaning the milk
container".
The hot water/steam connection noz-
zle (A8) is dirty.
Clean the connection nozzle as described in
section "12.11 Cleaning the hot water/steam
connection nozzle".
The milk contains
large bubbles and
squirts out of the
milk spout or there is
little froth.
The spout (C6) is dirty.Clean as described in section "11.5 Cleaning
the spout after use"
20. ELECTRICAL REQUIREMENTS UK ONLY
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt
about your supply contact your local electricity company.
The exible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not t the socket outlets in your home, it should be cut o and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might nd it and
plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched o when the machine is not in use.
IMPORTANT: the wires in the mains lead tted to this appliance are coloured in accordance with the following code:
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWN LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug.
If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualied electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualied electrician and should only be replaced
with a exible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be retted. If the fuse cover is lost, the plug must not be used until a replacement cover is
obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always
state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be tted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for DeLonghi ECAM45.760 Eletta Cappuccino at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of DeLonghi ECAM45.760 Eletta Cappuccino in the language / languages: English as an attachment in your email.
The manual is 2.95 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
Others manual(s) of DeLonghi ECAM45.760 Eletta Cappuccino
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
