Manual Defort DDT-1400A (page 5 of 28) (English, French)

555834

Zoom out

Zoom in

1/28

Also try to keep the total amount of work performed

in a single day under 2 hours or less. h. Be sure to

keep this manual handy so that you may refer to it

later whenever any questions arise.

• Always be sure to include this manual when selling,

lending, or otherwise transferring the ownership of

this product.

• Never allow children or anyone unablë to fully un-

derstand the directions given in this manual to use

this brush cutter.

WORKING GEAR AND CLOTHING

When using your brush cutter, you should wear proper

clothing and protective equipaient as follows.

• Helmet

• Protection goggles or face protector

• Thick work gloves

• Non-slip-sole work boots

• Ear protectors

And you should carry with you things as follows.

• Attached tools and ﬁ les

• Properly reserved fuel

• Spare biade

• Things to notify your working area (Tope, warning

signs)

• Whistle (for collaboration or emergency)

• Hatchet or saw (for removal of obstacles)

Never use your brush cutter when wearing pants with

loose cuffs, when wearing sondais, or when barefoot.

WARNING CONSIDTRÏNG

HANDLING OF FUEL

• The engine of this product is designed to run on a

mixed fuel, which contains highly ﬂ ammable gaso-

line. You should never store cans of fuel or reﬁ ll the

fuel tank in any place where there is a boiler, stove,

wood ﬁ re, electriçal sparks, weiding sparks, or any

otner source of heat or ﬁ re which might ignite the

fuel.

• Smoking while operatingMhe brush cutter or reﬁ lling

its fuel tank is extremely dangerous. Always be sure

to keèp lit cigarettes away from Ihe brush cutter at all

times.

• When reﬁ lling, the tank always turn off the engine

ﬁ rst and take a careful look around to make sure

that there are no sparks or open ﬁ ames anywhere

nearby before refueling.

• If any fuel spiliage oçcurs during refueling, use a dry

rag to wipe up spills before turning the engine back

on again.

• After refueling, screw the fuel cap back ttghtly onto

the fuel tank and then carry the brush cutter 1o a

spot 3m or more awayîrorrfwhere it was refueied be-

fore turning on the engine.

THINGS TO CHECK BEFORE USING YOUR

BRUSHCUTTER

• Before beginning work, look around carefully to get a

feel for the shape of the land, or grass to be trimmed

and whether or not there are any obstacle, which

might get in the way while working, and remove any

obstacles, which can be cleared away.

• The area within a perimeter of 15m of the person

using the brush cutter should be considered a haz-

ardous area into which no one snould enter while

the brush cutter is in use, and when necessary yel-

low warning rope, warning signs should be placed

around the work area. When work is to be performed

simultaneously by two or more persons, always

check the presence and locations of others so as to

maintain a distance each person sufﬁ cient to ensure

safety.

• Make sure that there are no loose screws or bolts,

fuel leaks, ruptures, dents, or any other problems,

which might interfère with safe operation. Be espe-

cialty careful to check that there is nothing wrong

with the blades or with the joints by which the blades

are attached to the brush cutter.

• Never use blades that are bent. warped, cracked,

broken or damaged in any way. e. Keep the blade

always sharp.

• Filling the cutting edges, keep the end corner sharp

and round the root of the edge.

• Check the boit to fasten the blade and be sure the

blade turns smoothly without abnormal noise.

NOTES ON STARTING THE ENGINE

1. Take a careful look around to make sure that no

obstacfes exist within a perimeier of 15m or less

around brush cutter.

2. Place the body of the brush cutler onto the ground

in a ﬁ ât clear area ana hold it ﬁ rmly in place so as to

ensure that neither neither the blades nor the throt-

lle corne into contact with any obstacles when the

engine starts up.

3. Place the throttle into the idling position when ster-

ling the engine.

4. After sterling up the engine. if the blades continue

lo rotale aven after the throttle has been moved

fully taack, turn off the engine and check the throtlle

wire and other parts.

KICKBACK SAFETY PRECAUTIONS

A dangerous reaction may occur when the spinning

blade contacts a solid cbject in the criticoi area. It is

called Kick back. As a resuit, the operator can lose con-

trol of the unit, which can cause serious or fatal injury.

Avoid kickbqck; observe the safety precautions below

strictly.

1. Before beginning work, clear your working area and

remove grasses around the obstacles.

2. When using your brush cutter, do not grip other

paris except the handles.

3. When using your brush cutter, never take your eyes

off. If you need to, place the throttle into the idling

position.

4. When using your brush cutter, do not let the unit

get closer to your feet nor raise the unit above your

waist.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Defort DDT-1400A in the language / languages: English, French as an attachment in your email.

The manual is 1,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Defort DDT-1400A Manual

Product: