535593

Datalogic PowerScan D8590-DPM Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
Step 2 — Set Up Hardware (RS-232)
Hardware for RS-232
Installation Steps for RS-232
1. Power-off host.
2.
Connect 8-pin mini-DIN on cable to
POWERSCAN D8590.
3. Connect 9-pin D-sub connector to
host’s serial port.
4.
Connect cable to power supply
.
5. Plug in power supply and power-
on host.
6. Start a terminal program (such as
Datalogic ESP’s Terminal or
HyperTerminal) and set to 57.6K baud, 8 data bits, none
parity, 2 stop bits.
7. Read the Reset to RS-232 Factory Defaults symbol, then
the Save Settings symbol.
1
POWERSCAN D8590 DPM
Imager, RS-232
PD8590-DPM
3
Kit, RS-232, 8’ coiled, US power
supply
CAB-532-KUS
Kit, RS-232, 8’ coiled, EU power
supply
CAB-532-KEU
Kit, RS-232, 8’ coiled, UK power
supply
CAB-532-KUK
RS-232 Configuration
Reset to
RS-232
Factory
Defaults
Save
Settings
Test
Symbol
Quick Start Guide
POWERSCAN D8590
Handheld DPM Imager
Step 2 — Set Up Hardware (USB)
Note: The USB interface draws its power from the host.
Hardware for USB
Installation Steps for USB
1. Connect the USB cable to the host.
2. Open any program in your host
computer that can receive
keyboard
text, such as Notepad.
3.
Read the
Reset to USB Factory
Defaults symbol below.
Note: If you want symbol data to be
entered as keyboard text, read the
USB Keyboard Mode symbol
below.
4. Read the Save Settings symbol below.
1
POWERSCAN D8590 DPM
Imager, USB
PD8590-DPM
2 USB Cable Included
USB Configuration
Reset to USB
Factory
Defaults
Save
Settings
Test Symbol
USB Keyboard
Mode
Step 1 — Check Required Hardware
Parts List for USB POWERSCAN D8590:
1. One POWERSCAN D8590 Handheld DPM Imager
2. One 12 ft. USB cable (pre-attached to imager)
Parts List for RS-232 POWERSCAN D8590:
The RS-232 cable is affixed to the handle with two screws, a spacer,
and a cable clip, which can be removed.
1. One POWERSCAN D8590 Handheld DPM Imager
2. Cable clip attachment
3. Spacer
4. Two threaded screws
5. RS-232 Interface Kit
• 8 ft. coiled RS-232 cable
• Power supply (U.S. Euro, or UK)
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. PowerScan is a
registered trademark of Datalogic ADC, Inc. in many countries, including the
U.S.A. and the E.U. All other brand and product names may be trademarks
of their respective owners.
Step 3 — Install ESP
Click on the ESP icon to run Datalogic ESP.
Note: Datalogic ESP can be installed from the Support Area at
www.adc.datalogic.com.
Minimum System Requirements
• 166 MHz Pentium processor (Pentium II processor recommended)
• Windows Vista, XP, or 2000 operating system
• Internet Explorer 5.0 or higher
• 64 MB minimum RAM (128+ MB RAM recommended)
• 80 MB hard drive space
• 800 x 600 minimum 256 color display (1024 x 768 32-bit color
recommended)
Important: The imager must be in USB or RS-232 Mode to connect
to
ESP
. Read the symbol below that corresponds with your communication
interface, and then read the Save Settings symbol.
USB
Mode
RS-232
Mode
Save
Settings
Step 4 — Select Model
When you start ESP, the model menu will appear.
1. Click the POWERSCAN D8590 button and then click OK.
If you do not want to make this selection every time you
start ESP, uncheck “Show this dialog at startup”.
2. Select the default imager name (POWERSCAN D8590-1),
or type a
name of your choice in the
Description
text field and
click
OK
.
3. Click Yes when this dialog appears:
820057290 (Rev A) May 2013
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Datalogic PowerScan D8590-DPM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Datalogic PowerScan D8590-DPM in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info