Manual DAP Audio Core Scratch (page 4 of 16) (English)

613019

Zoom out

Zoom in

1/16

Core Scratch

D2312

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance of

this manual or any unauthorized modification to the system.

 Never let the power-cord come into contact with other cables! Handle the power-cord and all

connections with the mains with particular caution!

 Never remove warning or informative labels from the unit.

 Never use anything to cover the ground contact.

 Never leave any cables lying around.

 Do not insert objects into air vents.

 Do not connect this system to a dimmer pack.

 Do not switch the system on and off in short intervals, as this would reduce the system’s life.

 Do not open the device and do not modify the device.

 Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output.

 Do not plug Mics into the console (or stag box) while Phantom Power is on. Also mute the monitor /

Pa system when turning Phantom Power on or off. Allow the system to adjust for a couple of seconds,

before setting the input gains.

 Only use system indoor, avoid contact with water or other liquids.

 Avoid flames and do not put close to flammable liquids or gases.

 Always disconnect power from the mains, when system is not used. Only handle the power-cord by

the plug. Never pull out the plug by tugging the power-cord.

 Always operate the unit with the AC ground wire connected to the electrical system ground.

 Make sure you don’t use the wrong kind of cables or defective cables.

 Make sure that the signals into the mixer are balanced, otherwise hum could be created.

 Make sure you use DI boxes to balance unbalanced signals; All incoming signals should be clear.

 Make sure that the available voltage is not higher than stated on the rear panel.

 Make sure that the power-cord is never crimped or damaged. Check the system and the power-

cord from time to time.

 Please turn off the power switch, when changing the power cord or signal cable, or select the input

mode switch.

 Extreme frequency boosts in connection with a high input signal level may lead to overdriving your

equipment. Should this occur, it is necessary to reduce the input signal level by using the INPUT

control.

 To emphasize a frequency range, you don’t necessarily have to move its respective control upward;

try lowering surrounding frequency ranges instead. This way, you avoid causing the next piece of

equipment in your sound path to overdrive. You also preserve valuable dynamic reserve

(“headroom”)

 Avoid ground loops! Always be sure to connect the power amps and the mixing console to the

same electrical circuit to ensure the same phase!

 If system is dropped or struck, disconnect mains power supply immediately. Have a qualified

engineer inspect for safety before operating.

 If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not

switch it on immediately. The arising condensation water might damage your system. Leave the

system switched off until it has reached room temperature.

 If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit securely

(preferably in the original packing material) and return it to your Dap Audio dealer for service.

 Repairs, servicing and electric connection must be carried out by a qualified technician.

 For replacement use fuses of same type and rating only.

 WARRANTY: Till one year after date of purchase.

Disposing of this product should not be placed in municipal waste and should be

separate collection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DAP Audio Core Scratch in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DAP Audio Core Scratch Manual

Product: