566592
2
Zoom out
Zoom in
Previous page
1/2
Next page
DKCD VI.51.T6.02 1/2003
Installation Instructions
Radiator thermostat RA 2000, tamper-proof model
Installation, temperature setting, limiting and blocking, theft protection
The clamping bland can be
rotated to one of four posi-
tions to allow easier access
to the allen screw.
Loosen screw if required.
Remove the valve cover.
Check that the thermostat is
set at the factory setting of 5.
Theft protection
Example: Required locked value = “3”
- Set thermostat at a setting below "3".
- Place one pin opposite the 3 on the
back.
- Turn the thermostat to setting "3".
- Place the second pin opposite the 2
on the back.
Example: Required min. value = “2”
- Set thermostat at a setting above "2".
- Remove a pin from the bottom of the
thermostat with the threaded screw-
driver and fit it at the position marked
2 on the back of the thermostat black
cover.
Example: Required max. value = “4” - Set
thermostat at a setting below "4".
- Remove a pin from the bottom of the
thermostat with the threaded screwdriv-
er and fit it at the position marked 4 on
the back of the thermostat black cover.
Push the thermostat firmly
onto the valve until an au-
dible "click" is heard.
Installation
Accessories
Theft protection devices (20pcs) 013G1232
Limit pins (10pcs) 013G1246
Range limiting pins 013G1237
Danfoss screwdriver set 013G1236
Threaded screwdriver 013G1231
Scale covers (20pcs) 013G1672
Limiting and blocking the setting range
Temperature setting
The required room temperature is
obtained by turning the thermostat
knob. The numbers on the dial cor-
respond to the approximate tem-
peratures of the scale.
The temperatures indicated are
guidelines only. The actual room tem-
perature will depend on structural fac-
tors affecting the thermostats, location,
etc.
45 49 57 63 68 73 79 82°F
7 9,5 14 17 20 23 26 28°C
l 1 2 • • 3 • • 4 5 l
= Frost protection setting
Lower limit setting (min. setting)
Locking setting
Upper limit setting (max. setting)
The remote sensor must not
be in a drafty location or be
covered. Do not install above a
heat source. Attach the sensor
bracket to the desired location.
Pull out the required length of
capillary tube and secure to
the sensor as shown. Push the
sensor onto the base.
Mounting thermostat with built-in sensor Mounting thermostat with remote sensor
The setting window can be covered us-
ing scale covers that are available as
an accessory.
Push the theft protection device into
the hexagonal hole of the allen screw.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Danfoss RA2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Danfoss RA2000 in the language / languages: English as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Danfoss RA2000

Danfoss RA2000 User Manual - English - 2 pages

Danfoss RA2000 User Manual - German - 8 pages

Danfoss RA2000 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info