654602
1
Zoom out
Zoom in
Previous page
1/2
Next page
1
GP Programmers & Timeswitches
102, 103 and 106 Models, for time control of Domestic Central
Heating Systems.
Wallplate/
Terminal Block
Plug-in Module
INSTALLATION AND WIRING INSTRUCTIONS
SPECIFICATIONS
Power Supply : 220/240Vac, 50/Hz
Switch Action : 1 x SPST, Type 1B
Switch Rating : 220/240Vac, 50/60Hz, 6(2)A.
Timing Accuracy : ± 1 min./month
Enclosure Rating : IP20
Pollution Situation : Degree 2
Max. Ambient Temp. : 55°C
Designed to meet BS EN60730-2-7
Dimensions : 112mm wide, 135mm high, 69mm deep
Rated Impulse voltage : 2.5kV
Ball Pressure Test : 75°C
The unit must be installed by a competent electrician and the installation
should conform to I.E.E. Regulations. This unit should be wired via full
disconnect in accordance with BS EN60730-1, e.g. via a plug and unswitched
socket or double pole switch outlet with neon.
INSTALLATION INSTRUCTIONS
1. Loosen the fi xing screw in the base of the unit to release the grey
plastic Wiring Cover. Ensure the protective tape over the thumbwheel
remains in place.
2. Holding the unit clockface downwards, press fi rmly in the centre of
the wallplate and slide it from the module as shown.
3. Fix the Wallplate/Terminal Block to the wall with countersunk No.8
woodscrews or to a steel box to BS 4662. 1970 or a surface mounting
steel or moulded box having centres of 2
3
/
8
" (60.3mm).
4. Referring to the Wiring Diagrams overleaf, connect the unit as shown.
Ensure that terminals 3 and 6 are linked where required (Mains
Voltage applications) with insulated cable capable of carrying full load
current.
5. Ensure all dust and debris have been cleared away from the area, then
plug the module fi rmly into the wallplate ensuring that the hook at
the top of the wallplate engages with the slot at the back of the body.
Press the module down until it locates solidly.
6. Cut a cable aperture in the Wiring Cover if necessary; replace the Wiring
Cover, and tighten the fi xing screw.
7. Switch on Mains and test for correct operation as follows:
i) Remove protective tape from the pre-selector wheel.
ii) Remove the dial cover and rotate the clock dial two complete
revolutions to clear the mechanism.
ii) Check that all positions of the Selector Switch and Tappets operate
correctly. (See instructions in User Booklet.)
8. Replace the dial cover. Finally leave the USER INSTRUCTIONS with the
Householder.
9. If the unit is to be left turned off and is in a dusty atmosphere, protect
the pre-selector wheel by re-affi xing the protective tape.
IMPORTANT: Remove tape prior to putting unit into service.
Plug-in Replacement
Module
Selector Switch
Wallplate/Terminal Block
Pre-Selector Wheel
This product complies with the following EC Directives:
Electro-Magnetic Compatibility Directive.
(EMC) (2004/108/EC)
Low Voltage Directive.
(LVD) (2006/95/EC)
1


Need help? Post your question in this forum.

Forumrules
1

Forum

danfoss-106

Reset search

  • Hello can I plug a danfuss 106 straight replacement for a 102 Submitted on 15-12-2021 at 17:08

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Danfoss 106 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Danfoss 106 in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info