757624
16
Zoom out
Zoom in
Previous page
1/17
Next page
Instruction Booklet3-Series
14
TROUBLESHOOTING
Flash Code/Fault Impact
on Scooter Notes
1. Battery needs
recharging Will drive
Battery charge is running Iow.
Recharge the batteries as soon as possible.
6. Out of neutral at
power-up Drive
inhibited
thunb lever is not in neutral position when turning
key switch on. Return thunb lever to neutral, turn
power off, and back on again. thunb lever may
need to be re-calibrated (see Section 4.2.3).
Check thunb lever wiring.
7. Speed Pot error Drive
inhibited
The thunb lever or its wiring is faulty. Check for
open or short circuits. thunb lever may not be
correctly set up. Contact your service agent.
8. Motor volts error Drive
inhibited
The motor or its wiring is faulty. Check for
open or shot circuits. Contact your service
agent.
9. Other internal
errors Drive
inhibited Contact your service agent.
Drive
inhibited
Battery charge is empty. Recharge the batteries.
If the scooter is left off for a few minutes, battery
charge might recover enough to allow driving
for a short time.
2. Battery voltage
too Iow
Drive
inhibited
The scooter has drawn too much current for
too long, possibly because the motor has been
over-worked, jammed or stalled. Turn the scooter
power off, leave for a few minutes, and then
turn the power back on again. The controller
has detected a shorted motor. Check the loom
for shorts and check the motor. Contact your
service agent.
4. Current limit
time-out
Drive
inhibited
Battery charge is too high. If a charger is
plugged in, unplug it or turn the Charge/Run
switch to Run. Scooters powered by RHINO
charge the batteries when travelling down
slopes or decelerating. Excessive charging
in this manner can cause this fault. Turn the
scooter power off then on again. If necessary,
reduce speed when descending the slope.
3. Battery voltage
too high
Drive
inhibited
Check that the park-brake release lever is in
the engaged position. Check that the motor/
park-brake connector is plugged in firmly. The
park-brake coil or wiring is fauly. Check the
park brake and wiring for open or short circuits
If necessary, unplug the motor/park-brake
connector and check that all four pins are in the
correct position. If this flash code does not
appear until the throttle has been moved out of
neutral, check for a short in the park-brake
circuit. If this flash code appears at power-up,
check for an open circuit in the park-brake
circuit. Contact your service agent.
5. Brake fault
To check the Self-Diagnostic Warning Light, turn on the key and count the number of flashes.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for CTM Homecare HS-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of CTM Homecare HS-360 in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info