498270

Crunch GPX 2000.1D Manual

10
Zoom out
Zoom in
Previous page
1/12
Next page
10
ENG
SUBWOOFER CONNECTIONS
- The total loudspeaker impedance should not be lower than 1 ohm.
- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.
If the amplifier is operated with a too low impedance or incorrectly used, the entire sound system
may be damaged. This means a warranty void in such cases.
SIGNAL OUTPUTS TO CONNECT ADDITIONAL AMPLIFIERS
The stereo signal connected to LINE INPUT (Fig. 1,3) will be routed in summed to the output jack OUT
(Fig. 1, 2b). This connection is suited to drive another identical GPX2000.1D amplfier at its input jack
(Fig. 1, 2b). Please check for this mode the section ”Master/Slave Operation” on the bottom of this
page.
OPERATING ELEMENTS
The input sensitivity can be adjusted to any headunit. Turn the volume control of your headunit to the
center medium position and then adjust the input level controls (Fig. 1,5) until you have an average
medium level. This setting usually provides sufficient power reserves at optimum weighted noise voltage.
INPUT SENSITIVITY
The subsonic filter is suited to filter the lower frequencies out from the audio signal to avoid unwanted
hum noises from the subwoofer. Set the desired crossover frequency of the subsonic filter by using
the controller (Fig. 1, 7). Thus to that only the frequencies above the chosen crossover frequency will
be amplified and the subwoofer plays more precised and efficient.
VARIABLE SUBSONIC FILTER
Set the desired crossover frequency of the low pass filter by using the controller (Fig. 1, 6). Thus to
that only the frequencies below the chosen crossover frequency will be amplified and the subwoofer
plays more precised and efficient.
VARIABLE LOWPASS FILTER
By using the bass boost controller (Fig.1, 9) you are able to increase the bass boost level from 0 dB to
12 dB. Use the frequency controller (Fig. 1,8) to set the desired frequency for the bass boost level. The
frequency range goes from 30 Hz to 80 Hz.
Caution: Please use the bass boost with care. A too high bass boost may result in serious damages
on the subwoofer.
VARIABLE BASS BOOST WITH VARIABLE FREQUENCY CONTROLLER
The Master/Slave Operation allows to link two identical GPX2000.1D amplifiers. This means you can
connect the in- and outputs of both amplifiers (Fig. 1, 2a and 2b) by a RCA patch cord. Amplifier 1
(Master) sends a summed mono signal to amplifier 2 (Slave). The advantage of this function is, that
the crossover section of amplifier 2 will be bypassed and for both amplifiers the same crossover settings
come into operation, which can be adjusted on the amplifier 1. Then both amplifiers work together as
one big monoblock.
Please observe therefor the section ”MASTER/SLAVE OPERATION (Fig. 5) WITH 2 GPX2000.1D on
page 12 and the figure 5 on the very last page.
MASTER/SLAVE OPERATION
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch GPX 2000.1D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch GPX 2000.1D in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info