498246
17
Zoom out
Zoom in
Previous page
1/28
Next page
17
General Installation Notes
The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such
as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and
protection from moisture. When considering the mounting location you should minimize the length of the
power and speaker leads. Minimizing both leads will yield a more reliable installation. It is also important
to ensure that the heat sink fins are not against a panel or a surface, preventing air circulation. Do not
install the amplifier on a subwoofer box or on vibrating parts of the vehicle, since the vibrations can cause
damage to the amplifiers electrical components.
Installation of the amplifier
Mark the location for the mounting screw holes by using the
amplifier as a template. Drill holes at the marked locations and
firmly fasten the amplifier in place with the mounting screws
supplied in the accessory kit.
Before drilling or cutting any holes, investigate the layout of your
automobile thoroughly: Take care when working near the gas lines
or hydraulic lines and electrical wiring.
Electrical Connection
Ground (GND)
This wire is the electrical ground and must be fastened securely to the vehicle chassis. The best method is to use a threading sheet
metal screw since the threads cut into bare metal. Ensure that all paint or other insulation is remove from around the hole area, and
using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable as possible - use the
same gauge as was used for the +12V cable. Make sure that the connection is safe, a loose connection may result in amplifier noise
and fault condition.
Remote (REM)
Many radios or other music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio
doesn't have a remote turn-on feature, then you can use the antenna relay wire, which activates the antenna motor. Please note, if the
power antenna retracts when the radio is operating, then you cannot use the antenna relay wire to operate the remote turn-on.
Batterie Connection (+12V)
This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an assigned fuse
in line with the + power supply wire. Please use a sufficient gauge for the installed amplifiers (min. 10-16 mm² for GP1000.2 and
GP1000.4 or min 16-25 mm² for GP1500.2 and GP1500.4).
This connection must be Completed using spade lug with
Insulating sleeve.
Fuses
The integrated amplifier fuses protect the units from
short circuit and overload. The fuse rating is for 4 Ohm
loads (impedance) of the speakers, for 2 Ohm loads
the fuses may have to get increased by up to 50%
in case of higher power consumption.
CHASSIS
GROUND
Remote
CHASSIS
GROUND
Battery
Fuse
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch GP1500.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch GP1500.4 in the language / languages: English, German as an attachment in your email.

The manual is 4,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info