581450
5
Zoom out
Zoom in
Previous page
1/52
Next page
XTi2 Series Power Amplifiers
page 5
Operation Manual
Get Started
Factory Preset #3: XOVER
Putting the amplifier in XOVER mode enables a 1.2kHz 4th order (24dB/octave)
filter that sends frequencies of 1.2kHz and below to Channel 1 output and
frequencies of 1.2kHz and above to Channel 2 output. The XTi2 Series amplifiers
come pre-loaded with a preset that makes it easy to configure the amplifier for
this operation.
Before you get started ensure that you:
1.
Connect signal source to Channel 1 ONLY using an XLR connector (the
amplifier inputs will automatically be put into Y mode when selecting this
preset).
2.
Connector the speaker as shown.
a.
Connect the speaker you wish to receive the low and mid frequencies (1.2kHz and below) to Channel 1 output
using Speakon
®
, Banana Plugs, or bare wire.
b.
Connect the speaker you wish to receive the high frequencies (1.2kHz and above) to Channel 2 output using Speakon
®
, Banana Plugs, or bare wire.
Follow these quick steps to configure the amplifier for XOVER operation:
1.
Push the “Set/Enter” button and you will see the word “Preset” flashing.
2.
Push the “Set/Enter” button again to enter the list of presets in the amplifier.
3.
Push the “Next/Down” or “PREV/UP” button until the screen displays “BIAMP”.
4.
Push the “Set/Enter” button to confirm your selection.
5.
The display will now read “BIAMP” with the Y icon and XOV icon highlighted.
LOW 1+/–
HIGH 2+/–
Factory Preset #4: BRG SUBS
Putting the amplifier in BRG SUBS (bridged subs) mode allows you to
bridge the amplifier for use with a single 8 or 4 ohm subwoofer. The inputs
are automatically summed, a 90Hz 4th order (24dB/octave) LowPass filter
is enabled, and the output mode is put into bridge-mono mode. The XTi2
Series amplifiers come pre-loaded with a preset that makes it easy to
configure the amplifier for this operation.
Before you get started ensure that you:
1.
Connect signal source to Channel 1 and Channel 2 using XLR
connectors (the amplifier inputs will automatically be summed together
when selecting this preset).
2.
Connector the speaker as shown.
a.
If using the binding post outputs, connect the positive terminal of the
speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.
b.
If using a Speakon
®
connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only.
Follow these quick steps to configure the amplifier for XOVER operation:
1.
Push the “Set/Enter” button and you will see the word “Preset” flashing.
2.
Push the “Set/Enter” button again to enter the list of presets in the amplifier.
3.
Push the “Next/Down” or “PREV/UP” button until the screen displays “XOVER”.
4.
Push the “Set/Enter” button to confirm your selection.
5.
The display will now read “XOVER” with the Y icon and XOV icon highlighted.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crown XTi 6002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crown XTi 6002 in the language / languages: English as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info