Manual Cresta WX688 (page 2 of 2) (English)

460510

Zoom out

Zoom in

1/2

switch to the pre-alarm display using the ALARM

button and then activate it by pressing the up arrow

button. The pre-alarm time is set to 15 minutes by

default; if you want to change this to 30, 45, 60 or 90

minutes, simply press and hold the ALARM button for

approx. 3 seconds until the minutes start to flash.

Select your desired pre-alarm time using the arrow

buttons and confirm your entry by pressing the

ALARM button.

If the alarm starts to sound you can stop it immediately

by briefly pressing the ALARM button. In this

situation press the up or down arrow button to switch

off the alarm completely (OFF is displayed). If you do

not press the button the ALARM will automatically

stop after 2 minutes.

1.9 MIN./MAX. MEMORY FOR TEMPERATURE

To view the maximum and minimum values for

temperature and humidity press the MEM button in the

battery compartment of the weather station; press it

once to display the minimum values, twice to display

the maximum values and three times to the return to

the normal display.

1.9.1 ERASING THE MIN./MAX. MEMORY

To erase the stored maximum and minimum

temperature values press and hold the MEM button for

approx. 3 seconds.

1.10 ATMOSPHERIC PRESSURE DISPLAY

The atmospheric pressure is measured every hour,

starting from the time the batteries are inserted into in

the base station. By pressing the PRESSURE/

ALTITUDE button in the battery compartment of the

weather station you can alternate between absolute

atmospheric pressure (LOCAL), relative atmospheric

pressure (SEA LEVEL) and the set altitude.

You can view the atmospheric pressure for the past 36

hours by pressing the HISTORY button. The respective

hour is indicated in the small display field located to

the right of the moon phase display.

Setting the units of measurement:

You can alternate between two units of measurement

for the height above sea level and the atmospheric

pressure by pressing the UNIT button in the weather

station's battery compartment.

Simply switch to the relevant display by pressing the

PRESSURE/ALTITUDE button and then press and

hold the UNIT button for approx. 3 seconds. The

respective unit of measurement starts to flash.

You can now use the arrow buttons in the weather

station's battery compartment to alternate between

hPa/mBar and inHg for the atmospheric pressure and

between Meter and Feet for the height above sea level.

Confirm your selection by pressing the UNIT button

again.

The weather station also has a graphical display to

indicate the atmospheric pressure over the past 12

hours.

1.11 WEATHER FORECAST

The weather forecast is an approximate indication that

is calculated for the next 12-24 hours over a radius of

approximately 30 to 50 km. It is based on the

fluctuations of atmospheric pressure and it predicts

actual weather conditions with an accuracy of 70%. As

it is not possible to predict the weather with 100%

accuracy, we do not accept any liability for damage

which may occur as a result of an incorrect weather

forecast.

The weather forecast is displayed using the following

symbols:

Indicator

displays on

the unit

Forecast

Sunny

Slightly

Cloudy

Rainy

Snowy

1.12 WEATHER TREND DISPLAY

The weather station is also able to display the weather

trend. This is also based on the fluctuations of

atmospheric pressure and it is indicated by three arrows

to the left above the weather forecast. If the

atmospheric pressure falls drastically, the arrow in the

trend display will point downwards. If the atmospheric

pressure increases drastically, the arrow in the trend

display will point upwards. If the atmospheric pressure

stays roughly the same, the arrow will remain

horizontal.

1.13 TREND DISPLAY FOR INTERNAL AND

EXTERNAL TEMPERATURE AND

INTERNAL AND EXTERNAL HUMIDITY

The development of the values for external

temperature, internal temperature and humidity is

indicated by an arrow to the right or left of the

respective field. If the value changes dramatically

within one hour, this will be indicated by an upward or

downward pointing arrow. If there has been no change,

a horizontal arrow is displayed.

1.14 COMFORT DISPLAY FOR ROOM

CLIMATE PROVIDED BY THREE

SYMBOLS (WET, COMFORT AND DRY)

The weather station indicates the room climate via

three symbols located to the right above the internal

humidity display: WET indicates a humidity level

above 70%; COMFORT indicates a humidity level of

40% - 70% and 20°C - 25°C; and DRY indicates a

humidity level below 40%.

1.15 ADJUSTABLE ALARM FOR EXTERNAL

TEMPERATURE

The weather station can store an individually adjustable

alarm for each external sensor; it then sounds the alarm

if the temperature falls below or exceeds the specified

limit. To display the temperature alarm briefly press the

TEMP AL. button. The upper limit is displayed initially

(default setting 70°C). To access the setting mode

simply press and hold the TEMP AL. button for approx.

3 seconds. The set upper limit starts to flash. Now use

the arrow buttons to set your desired upper limit and

then confirm your selection by pressing the TEMP AL.

button. Then press the TEMP AL. button twice briefly

to display the lower limit (default setting -50°C). To

access the setting mode for the lower limit press and

hold the TEMP AL. button again for approx. 3 seconds.

The set lower limit then starts to flash. Use the arrow

buttons to set your desired lower limit and then confirm

your selection by pressing the TEMP AL. button again.

The temperature alarm is now set and active.

1.16 MOON PHASE DISPLAY

The display for the current moon phase is located to the

left below the atmospheric pressure display. The moon

phase depends on the current date and is displayed with

the following symbols:

You can display the moon phases for the previous and

next 39 days by using the arrow buttons in the weather

station's battery compartment. The respective day is

indicated in the small display window located to the

right of the moon phase display.

New

Moon

Waning

Crescent

Waning

Crescent

First

Quarter

Waxing

Gibbous

Full

Moon

Waning

Gibbous

Last

Quarter

1.17 LOW BATTERY DISPLAY

Weak batteries in the base station and external sensor

are indicated by the low battery display. We

recommend you operate the weather station with

ordinary batteries as opposed to rechargeable batteries.

1.18 TROUBLESHOOTING

Please check the batteries before issuing a complaint

about the weather station and replace these, if

necessary, with new batteries.

The external temperature is no longer displayed on the

base station: If the external sensor no longer registers,

this may be for one of the following reasons:

• The batteries in the external sensor and/or base station

are too weak. Replace the old batteries. Never use a

mixture of old and new batteries and proceed as

described under the section entitled "Sensor call

button" to re-register the sensor.

• External sensor reception is interrupted by obstacles.

As these are often impossible to remove (e.g.

thermopane glazing, walls with steel reinforcements

or certain concrete compositions, steel bearers, etc.),

please reduce the distance between the external

sensor and the base station.

• If external temperatures fall below 0°C, the battery

power of the external sensor diminishes and the radio

transmission signal becomes weaker. In this case

please reduce the distance between the external

sensor and the base station.

• If the base station does not display the external

temperature but only "- - - -", it may be because the

batteries in the base station are too weak, meaning it

is unable to receive the signals from the external

sensor. Replace the batteries with new ones.

• Interruptions to reception can also be caused by other

household equipment, TV and radio remotes,

interfering transmitters or external transmitters, etc.

In this case only "- - - -", "HHH" or "LLL" can be

seen on the display. If this occurs, press and hold the

down arrow button for approx. 5 seconds to start the

sensor scanning process. Then wait a few moments.

The current external temperature should be displayed

again after the external sensor's next transmission

signal.

• Weak batteries in the base station

Replace the batteries as soon as the low battery

symbol is displayed. Wait for approximately 5

minutes before inserting the new batteries. Do not

touch the battery contacts when inserting the batteries.

This will reduce the corrosion behaviour of the

contacts and extend the life of the batteries. When

inserting the new batteries always make sure the

polarity is correct. After changing the batteries

proceed as described under section 1.3

"Commissioning".

• Weak batteries in the external sensor

Replace the batteries as soon as the low battery

symbol is displayed. When inserting the new batteries

always make sure the polarity is correct. The external

sensor must then be registered again. To do this

proceed as described under section 1.3

"Commissioning".

• Incorrect temperature and humidity display.

The temperature and humidity display are affected by

direct sunlight and rain respectively. Please position

the external sensor in such a way that it is not

exposed to direct sunlight or rain.

11 12

13 14

15 16

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cresta WX688 in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cresta WX688

Cresta WX688 User Manual - German - 2 pages

Cresta WX688 User Manual - Dutch - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cresta WX688 Manual

Product: