498196
3
Zoom out
Zoom in
Previous page
1/16
Next page
Hot and Cold Fill Connection
1. Connect the straight end of the supplied RED or GREY hose to
the HOT water supply tap (Fig 1). Connect the straight end of
the supplied BLUE hose to the COLD water supply tap.
2. Hand tighten connectors sufficiently to ensure water does not
leak from the hose connections.
3. Before connecting each of the hoses to the appliance, confirm
the water supply is flowing by holding the free end of each
hose in a bucket, turn the relevant water supply taps on and
then off.
4. Connect the angled end of the RED or GREY hose to the white
plastic inlet valve marked ‘H (Fig 2) and the angled end of the
BLUE hose to the white plastic inlet valve marked Cat the back
of the appliance.
5. Hand tighten connectors sufficiently to ensure water does not
leak from the hose connections.
6. Turn on the water supply taps and check for leaks from the connectors. In the event
of a leak,turn off supply tap, remove connector and check that the sealing washer is
in place. Refit the connector and tighten. Turn on water supply taps.
Cold Fill Only Connection
A Cold Fill Adaptor is available from your local Creda authorised Service
Centre.
1. Connect angled end of supplied hoses to hot and cold inlets
at the back of appliance
2. Connect straight end of hoses to cold fill adaptor.
3. Connect adaptor to cold water supply.
NOTE: Hand tighten sufficiently to ensure water is not leaking from
the tap hose connections.
Fill Hoses
Ensure the supplied hoses are not kinked when connected.
2m long extension fill hoses are available from your local retailer
or Genuine Parts and Accessories UK 08709 077 077.
Water Pressure
Incoming hot and cold water pressure should be between 3 and 150
psi (21 - 1034 Kpa).
The temperature of the incoming household hot water supply should ideally be 60°C and
no higher than 70°C as this could cause damage to both your laundry and appliance.
Methods of Plumbing
The water supply taps must be easily accessible when the appliance is installed. Your
taps should be in good condition or it may leak when turned full on. Mixer taps are
unsuitable, if you have them you will need to use permanent plumbing.Adaptors are
required to connect to sink taps.
Permanent Plumbing
There must be taps or stopcocks so that the water supply can be turned off, isolating
the appliance from the household supply.
Existing Plumbing
If you have an existing installation please check that this includes taps or stopcocks to
isolate the appliance. The appliance must be connected to the water supply using
the new hose set supplied, old hose sets should not be used.
4. Remove 2
screws and
transit
bracket.
Retain for
future use.
3. Remove
1 screw and
clamp.
Retain for
future use.
Transit Bracket
Removal
Connecting to the Water Supply
3
5. Slide and
push work
top lid into
position
ensuring it
is located
on the
console
correctly.
2. From the
rear of
appliance,
grip the
sides of the
work top
lid, lift, slide
and pull
towards
you to
remove.
1. Remove
the 3
screws from
back of
work top
lid.
6. Replace
the 3
screws into
the back of
the work
top lid.
Inlet to machine
Cold
Water
Supply
After removing the packaging from the machine, ensure that the polystyrene pyramid
(shown at the side) has come away from the underside of the machine, with the
polystyrene base.
If it has not come away, remove it by tilting the machine backwards until the pyramid can
be seen and then remove.
Removing the Polystyrene Pyramid
Inlet to machine
Inlet to machine
Cold Water Supply
Fig. 3
Fig 2
Fig 1
Fig. 4
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Creda W120VW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Creda W120VW in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info