580573
2
Zoom out
Zoom in
Previous page
1/2
Next page
Technical data
Wheel circumference: 10-3999 mm
Default wheel circumference setting: 2205 mm
Battery type: CR2032
Battery life (1h/trip/day): approx. 2 years
Operating temperature: 0-40º C
Energy saving modus: after 5 min. of inactivity
Wake up: via push button or signal input
Warning
Remove the computer from the contact plate when not in use to increase the
lifespan of the battery. Storage of an unused computer in its holder for a period
longer than 14 days will result in a malfunction of the wake up feature.
Use the push button at the rear to activate the computer.
Do not expose the bicycle computer to direct sunlight when not in use.
Do not open the computer, unless changing batteries. To avoid possible
accidents do not occupy yourself excessively with the computer when riding.
Check the position of the sensor and magnet at regular intervals.
User’s instruction
Cordo FB6 bicycle computer
ENG
Display indicators
Flashing = bicycle in motion
Energy saving mode
Activated after 5 minutes inactivity
Tyre circumference
• Enter the tyre circumference in mm (see table below)
• Switch to the ATM mode (ATM = total riding time)
• Press MODE and RESET at the same time for
2 seconds to change the tyre circumference.
• Press RESET to alter digits.
• Press MODE to change to the next digit.
• After the 4th digit, press RESET to choose between km/h and mph.
• Press SET to save the settings.
1 Sensor activity
2 SCAN symbol
3 MODE symbol
4 Clock symbol
5 RESET button
Instructions for use
6 Speed
7 km/h or mph
8 Sub display
9 SET button (rear)
10 MODE button
1 Clock with 24 hour display
Press the MODE button and select Clock.
Press SET at the rear for 2 seconds. Select digits with
MODE. Set digits with RESET and press SET to save
settings.
2 DST / Distance
Total distance up to 99.999 km
3 ATM
Total riding time up to 9:59:59 h
4 ODO
Total distance: up to 99.999 km
Press MODE and select ODO modus.
Press SET at the rear for 2 seconds.
Press MODE to select the next digit.
Press RESET to alter digits.
Press SET to save the settings
5 RESET
Press MODE and select DST or ATM.
Press RESET for 2 seconds to reset DST or ATM.
6 SCAN
Press MODE for 2 seconds to activate SCAN.
SCAN only functions when the bicycle is moving.
Press SCAN again for 2 seconds to stop SCAN.
Assembly
1. Bicycle computer
2. Contact plate
with sensor
3. 3x rubber washers
(2x 32mm,
1x 42mm)
4. Base plate
5. Magnet
6. Battery (CR2032)
The bicycle computer is secured by turning it in a clockwise direction.
To remove the bicycle computer, turn it in an anticlockwise direction.
Contents of packaging Securing the bicycle computer
Assembly contact plate Fitting the sensor
Insert battery
Can be fitted to the handlebar or stem. To change the position,
loosen the base plate, turn it 90º and secure the contact plate again.
Use the rubber washers to fix the contact plate to the handlebar or
handlebar post.
1.
The sensor should be secured on the same side
as the bicycle computer using a rubber washer.
Use a coin to open and close the battery compartment.
Insert the battery with the + pole at the top.
Controlling the display after renewing the batteries will ensure
that they have been
properly placed.
2.
Screw the magnet onto a spoke.
3.
Align the center of the magnet to
the mark on the sensor.
The distance between the magnet and the
sensor should not exceed 5 mm.
www.cordo.com
1: attach 2: cllick and ‘turn 3: detach
contacts
centre of
the magnet
sensor
marking
click
2


Need help? Post your question in this forum.

Forumrules
1

Forum

cordo-fb6

Reset search

  • I’m pressing the button on the back yet nothing is happening. No display. The battery is fine ????? Submitted on 20-4-2020 at 12:35

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cordo FB6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cordo FB6 in the language / languages: Dutch as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info