652347
5
Zoom out
Zoom in
Previous page
1/56
Next page
5
2 For your safety
Intended use
Steam humidifiers Condair CP2 are intended exclusively for direct or indirect room
humidification within the specified operating conditions. Any other type of applica-
tion, without the written consent of your Condair supplier, is considered as not conforming
with the intended purpose. The manufacturer/supplier cannot be made liable for any
damages resulting from improper use. The user bears full responsibility.
Operation of the equipment in the intended manner requires that all the information in
these instructions is observed (in particular the safety instructions).
Please contact your local Condair distributor if the steam humidifier Condair CP2 is to be
used in a steam-bath.
General safety instructions
The steam humidifier Condair CP2 must only be installed, operated serviced and in all
cases repaired only by persons who are adequately qualified to undertake such
work and are well acquainted with the product. Ascertaining the qualifications is the
customers responsibility.
Caution, danger of electric shock! The Condair CP2 is operated with mains
voltage. Before commencing work on the Condair CP2, the unit is to be rendered
inoperative in accordance with section 6.3 and prevented from further inadvertent
operation (isolate unit from the electrical power supply, isolate water supply).
Observe all local safety regulations.
relating to the operation of mains-operated electrical and electronic equipment
and the provision of water, steam and electrical installations
Poorly maintained humidification systems can endanger health. The servicing inter-
vals should therefore be adhered to without reservation and the servicing work
carried out correctly.
If it is suspected that safe operation is no longer possible, then the Condair CP2
should immediately be shut down and secured against accidental power-up. This
can be the case under the following circumstances:
if the Condair CP2 is damaged
if the Condair CP2 is no longer operating correctly
if connections and/or piping are not sealed or cables are loose
The Condair CP2 must only be operated under the specified operating conditions
(see section 7).
The Condair CP2 is protected according to IP20. Make sure the units are installed in
a drip-proof location
Caution! If the Condair CP2 is installed in an area without a water drain, water sensors
must be fitted in the area, such that in the event of leakage in the water system, the water
feed is safely shut off.
Caution, danger of corrosion! In order to avoid damage, no corrosion-sensitive
components should be located in the area of the aerosol streams.
No work/repair should be carried out on the Condair CP2 other than that described in
these instructions.
Use exclusively original accessories and spare parts available from your Condair
supplier.
No modifications must be undertaken on the Condair CP2, the accessories and the
options without the express written consent of Axair Ltd.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Condair CP2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Condair CP2 in the language / languages: English as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info