738059

Concept2 SkiErg Manual

15
Zoom out
Zoom in
Previous page
1/20
Next page
15
0818
4
EN
FR
NL
SV
FI
DE
NO
Place a black spacer behind each mounting hole on the
SkiErg bottom bracket. Assemble a washer on a lag
screw and screw into each mounting hole until tight.
Wall Mounting Instructions for a Wall with Wooden Stud Spacing other than 16”
Prior to mounting your SkiErg to a wall with stud spacing other than 16” you must provide a solid attachment point by first securing
a wooden mounting plate to the wall. This wooden plate should be 1.5” thick and suitable for receiving the lag screws (provided in
parts bag) which will hold the SkiErg. You will need to provide lag screws and washers to attach this mounting plate to the wall.
1. Determine the location of the studs in your wall. Mark the center of the studs. Measure the distance between them.
2. Make 4 marks on each piece of wood 1” from the top, 1” up from the bottom, and separated by the stud spacing
in your wall.
3. Drill through holes at each of these locations.
4. Install the pieces of wood such that the center line of the top piece is 85” above the floor, and the lower piece
is resting on the floor. (Note, if you have a wooden baseboard, you may attach the SkiErg directly to the baseboard.)
5. You may now follow steps 2–4 from the previous SkiErg mounting instructions using the mounting hardware provided.
EN
Placez les entretoises noires derrière chaque trou sur
le support bas. Assemblez rondelle + tirefond et vissez
l’ensemble dans chaque trou.
Setzen Sie ein schwarzes Distanzstück hinter jedem
Montageloch an der unteren Halterung. Setzen Sie je
eine Unterlegscheibe auf die Schrauben und schrauben
Sie die untere SkiErg Halterung fest an.
Plaats een zwarte spacer tussen elke houder opening op
de onderste houder van de SkiErg. Bevestig de houder
met ring en schroef.
Placera en svart bricka mellan vägg och den nedre hållaren. Sätt
också dit en bricka på monteringsskruven innan den dras fast i
väggen. Drag fast skruvarna ordentligt.
Aseta musta muoviholkki SkiErgin ja seinän väliin. Aseta prikka
täkkipulttiin ennen kiristämistä.
Plassér en svart avstandsholder bak hvert hull på bunnbraketten.
Tre en skive på en treskrue og skru i hvert hull til den sitter
Instructions de fixation murale pour un mur en bois.
Avant de monter votre SkiErg contre un mur avec des montants espacés de plus de 40cm, vous devez sécuriser votre surface par le
montage d’une plaque de renfort (en bois). Cette plaque devra être épaisse de 4cm et appropriée pour recevoir des tirefonds (fournis)
qui tiendront le SkiErg. Vous aurez besoin de tirefonds et rondelles pour attacher cette plaque de montage au mur.
1. Déterminez l’emplacement des montants sur la cloison. Marquez le centre des montants. Mesurez la distance entre eux.
2. Tracez 4 repères sur chaque morceau de bois à 2,5 cm du haut et 2,5 cm du bas, séparés par la distance de la structure
en bois du mur.
3. Percez des trous de passage à chacun de ces emplacements.
4. Installez les morceaux de bois de telle sorte que l’axe central de celui du haut est à 218 cm au-dessus du sol et que celui
du bas repose sur le sol. (Remarque : si vous avez une plinthe en bois, vérifiez qu’aucun fil électrique passe dans celle-ci.
Vous pourez fixer le SkiErg directement à la plinthe.si elle est assez épaisse.)
5. Vous pouvez maintenant suivre les étapes de montage 2-4 du précédent Skierg et utiliser le matériel fourni.
FR
DK
ES
Placer et sort afstandsstykke bag hvert monteringshul på SkiErg
bund beslag. Saml en skive på træskrue og skru i på hvert hul.
Coloca un espaciador negro detrás de cada orificio de montaje en
el soporte inferior del SkiErg. Coloca una arandela en el tirafondo
y atorníllalo a cada orificio hasta que esté firme.
P
Coloque um espaçador por trás de cada furo de montagem no
suporte inferior do SkiErg. Colocar uma anilha e um parafuso e
apertar em cada buraco até fixar.
将黑色间隔件放置在SkiErg底部支架上的每个安装孔后。将垫圈安装到
拉力螺钉上，并拧入每个安装孔中直至拧紧。
中
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Concept2 SkiErg at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Concept2 SkiErg in the language / languages: English, German, Dutch, Danish, French, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Concept2 SkiErg

Concept2 SkiErg User Manual - English, German, Dutch, Danish, French, Portuguese, Swedish, Spanish, Norwegian, Finnish - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info