Manual Concept2 SkiErg (page 6 of 49) (English, German, Dutch, Danish, French, Portuguese, Swedish, Spanish, Norwegian, Finnish)

738059

Zoom out

Zoom in

1/49

0818

SkiErg Product Manual

MAINTENANCE

WARNING!

The safety level of the machine can be

maintained only if it is examined regularly

for damage and wear. Replace defective

components immediately to ensure safety

and performance or keep machine out of use

until repaired.

A minimal amount of periodic maintenance

will assure proper function and prolong the

life of your SkiErg. The PM will keep track of

Lifetime Meters (odometer). This will help

you determine when to perform maintenance

procedures. To view total meters on the PM

push Main Menu>More Options>Utilities>

Product ID>More Information.

On a Regular Basis

Untwist the Cords

When you grasp the handles to use your SkiErg,

you may be inadvertently twisting the cords,

much like what would happen to the cord on a

telephone handset. Over time, this may cause

the cords to twist around each other inside the

SkiErg resulting in a lumpy feeling when you

pull on the handles. This may cause premature

wear of the cord.

To avoid this, check the cords regularly and

untwist them as needed. You will be able to see

the twist in the cord; simply untwist by turning

the handle in the opposite direction to the twist.

Periodically untwist the cords. It will be easier if

you have another person help you.

1. Pull out both handles as far as they go

2. Hold the cords at the top bracket allowing

the handles to dangle and spin freely.

3. Run your hand down the length of each cord

to untwist the cord.

4. Return the handles to the top position.

5. Repeat the process starting at step 1 at least

two times.

Clean Grips

Use a mild soap or cleaning product to clean the

grips every few workouts as needed.

Every 500,000 meters

(approximately 50 hours of use)

Inspect the Cords

There are two separate cords and two bungee cords to

inspect.

Important! Each cord is of a speciﬁc type and should be

replaced with the appropriate Concept2 replacement cord

if signiﬁcant wear or damage is observed.

Cord Inspection:

1. The handle cords can be easily inspected by pulling

the handles all the way out and visually checking for

wear.

2. Inspect the cords

working inside the

vertical frame. Start by

removing the lower right

side cover by removing 8

screws, using the 6 lobe

driver provided with your

SkiErg. See illustration.

Once the cover is

removed, all cords and

pulleys will be visible.

3. Have a helper slowly

pull the handles all the

way out and observe the

condition of the handle

cords and the bungee cord. You should be able to see

the entire working length of all cords.

A Description of Cord Wear/Damage:

• The cords consist of a solid braid (not a covering

over inner ﬁbers). Over time the surface will show

“fuzzing.” If this “fuzzing” becomes worse in a

localized spot on the cord it is time to replace the

cord. See photo. We

recommend replacing

both cords at the

same time.

• The bungee cord

consists of elastic

ﬁbers encased in a

braided covering.

Some “fuzzing”

of the covering is

normal, but once

the white ﬁbers are

exposed the cord

should be replaced

immediately.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Concept2 SkiErg in the language / languages: English, German, Dutch, Danish, French, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Concept2 SkiErg

Concept2 SkiErg Installation Guide - English, German, Dutch, Danish, French, Portuguese, Swedish, Spanish, Norwegian, Finnish - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Concept2 SkiErg Manual

Product: