634405
16
Zoom out
Zoom in
Previous page
1/20
Next page
- 16 -
Fig.13A
NOTE: Replace the filter if frayed, torn, damaged or unable to be cleaned.
10.2 CUTTING BLADE
CAUTION: Be sure to disconnect and ground the spark plug wire before working on the cutting blade to prevent
accidental engine starting. Protect hands by using heavy gloves or a rag to grasp the cutting blades.
Tip the mower as specified in the separate engine manual. Remove the hex bolt and washer, which holds the blade and blade
adapter to the engine crankshaft. Remove the blade and adapter from the crankshaft.
When you change the blade, use the original type marked on the blade
Cobra Part Number 263001330 for the MX51SPH and M51SPH Available to order from your local dealer.
WARNING: Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when
necessary. For best results your blade should be sharp. Slightly worn blades may be re-sharpened with care. After removing the
blade, it may be ground or filed, so that the cutting edge is as close to the original bevel as possible. It is extremely important that
each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. Improper blade balance will result in
excessive vibration causing damage to the engine and mower. Be sure to carefully balance the blade after sharpening. The blade
can be tested for balance by balancing it on a round shaft screwdriver. Remove metal from the heavy side, until it balances
evenly.
Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the
blade adapter with light oil. Install the blade adapter on the crankshaft. Refer Fig.15. Place the blade with the part number facing
away from the adapter. Align the washer over the blade and insert the hex bolt. Tighten the hex bolt to the torque listed below:
Fig. 14
10.3 BLADE MOUNTING TORQUE
Center Bolt 40Nm.min, 50Nm.max. To ensure safe operation of your mower. All nuts and bolts must be checked periodically for
correct tightness. After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the
original shape. Cutting efficiently will be reduced and the blade should be replaced. Replace with an approved factory
replacement blade only. Possible damage resulting from blade unbalance is not the responsibility of the manufacturer.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra MX51SPH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra MX51SPH in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info