634408

Cobra MX515SPBI - DYM1588SD Manual

15
Zoom out
Zoom in
Previous page
1/19
Next page
- 15 -
adapter with light oil. Install the blade adapter on the crankshaft with the "star" away from the engine. Refer to figure 14. Place the
blade with the part number facing away from the adapter. Align the washer over the blade and insert the hex bolt. Tighten the hex
bolt to the torque listed below:
Fig.14
10.3 BLADE MOUNTING TORQUE
Center bolt 40Nm-50Nm, to insure safe operation of your unit. ALL nuts and bolts must be checked periodically for correct
tightness.
After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the original shape. Cutting
efficiently will be reduced and the blade should be replaced. Replace with an approved factory replacement blade only. Possible
damage resulting from blade unbalance condition is not the responsibility of the manufacturer.
When you change the blade, Must use the original type marked on the blade (Cobra 263001679)
10.4 ENGINE
Refer to the separate engine manual for engine maintenance instructions.
Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully.
Service air cleaner as per separate engine manual under normal conditions.
Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air
cleaner should be serviced.
To service the air cleaner, refer to the separate engine manual packed with your unit.
The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each
mowing season; check engine manual for correct plug type and gap specifications.
Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air
circulation which is essential to engine performance and life. Be certain to remove all grass, dirt and combustible debris from the
muffler area.
10.5 CLEAN THE DECK AND CUTTING BLADE
WARING: Before cleaning, stop mower and disconnect spark plug cable.
WARING: The cutting blade continues to rotate for a few seconds after the engine is shut off.
NOTE: Before cleaning, remove the grass bag and discharge channel, and then mount the mulching wedge.
To clean the mower deck underneath follow these steps:
1. Insert the hose connector into the cleaning hole-connector on the deck; ensure they are firmly connected (Fig.15A, Fig.15B);
2. Insert another end of the hose into the water tap and then open the switch
3. Connect the spark plug cable and then start the engine as same as the section 7.2;
4. After operating about five minutes, stop the water and the engine (disconnect the spark plug connection) and check the deck
and cutter, repeat steps 3 to 5 as necessary.
5. After cleaning take away the hose, and store in a clean and safety place;
6. Wipe the water from the deck and cutter surface, and then lightly grease the cutter to avoid corrosion and rust.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra MX515SPBI - DYM1588SD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra MX515SPBI - DYM1588SD in the language / languages: English as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info