565538
8
Zoom out
Zoom in
Previous page
1/20
Next page
vered with water, otherwise the appliance can
not switch o properly.
ATTENTION: Make sure not to ll water past the
MAX marking (= 1,7 l) on the water level display.
Scalding may result from water boiling over.
Close the lid manually and place the electric
kettle anywhere on the 360° contact base.
Your water boiler is equipped with a tempera-
ture control and works by touch (please see also
Touch control panel“).
Select the desired temperature (between 40°
and 100°C) by touching it on the Touch-Tempe-
rature Strip“. The LED display then lights up blue
to this point.
INFO: Water will boil at a temperature of 100°C.
Please observe that the water temperature after
boiling may deviate from the selected tempera-
ture by a few degrees Celsius.
To switch it on, press the ON/OFF switch on the
touch panel.
When the water reaches the desired tempera-
ture, the electric kettle will beep three times and
then switches o automatically.
The LEDs of the temperature control will light
up afterwards.
You can interrupt the boiling process at any time
by pushing up the ON/OFF switch again.
Please wait a moment until the water stops
bubbling.
To pour the water, lift the electric kettle from the
contact base.
IMPORTANT: Always make sure that the device
is switched o before removing the electric
kettle from the contact base.
Wait a few minutes to let the device cool off be-
fore filling it with water again and using it. Do
not touch the hot housing during operation.
Danger of burning!
Keeping warm function
You can keep the water hot after boiling.
Proceed as described in „Operation“, but push
the button for keeping warm instead of the ON/
OFF switch.
This automatically operates the ON/OFF switch
and the device starts to boil.
Then the water is kept warm on the selected
temperature.
You can remove the water boiler from the
contact socket at any time during the keeping
warm time, pour water and return it, which will
continue the keeping warm function.
You can stop the keeping warm function at
any time by pushing the keeping warm button
again.
Otherwise, the device will automatically switch
off after approx. 2 hours.
You may also switch on the keeping warm
button subsequently during a regular boiling
process.
For this, boil water as usual and select the
keeping warm button after pushing the ON/OFF
switch.
8
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Dear Customer
We wish you much pleasure with your new
electric kettle with touch panel.
Your Cloer Company
Preparation for use
Remove all packaging elements and labels, but
not the rating plate.
Place the electric kettle on a dry, even, non-slip
surface.
Before initial use
Please read these operating instructions care-
fully before using the device for the rst time
and save these instructions in case you want to
read it again.
Boil at least once 1.7 l water at 100°C, and then
pour this away.
Safety notices for use of the
contact base / electric kettle
Do not come below the MIN marking (= 0.8 l) on
the water level display, otherwise the appliance
can not switch o properly.
Do not ll the electric kettle with water past the
MAX marking (= 1,7 l) on the water level display.
Scalding may result from water boiling over.
Always remove the electric kettle from the
contact base before lling with water.
This electric kettle may only be used for heating
water.
Do not place this appliance on or near a hot gas
or electric burner.
Before operating the machine, make sure that
the contact base is dry.
Please make sure that water is never spilled on
the contact base.
If water is accidentally spilled onto the contact
base, proceed as follows:
Unplug the unit from the wall socket.
Dry the contact base with an absorbent
dry kitchen towel.
Dry the surface beneath the contact base.
Plug the unit into the wall socket again.
Never leave the appliance unattended when in
use.
CAUTION!
The surface is hot during
operation. Only touch the
device at its handle.
Touch control panel
Your electric kettle is equipped with a tem-
perature control and a “keep-warm“ function,
controlled by a modern touch control panel. For
both a temperature in the range of 40° -100°C
can be selected. The closed surface prevents
dirt, dust or water to get into the base interior.
Operation
Plug the power plug into the wall socket.
Remove the electric kettle from the contact
base.
Open the lid by pressing the cover release knob
at the handle.
Fill the electric kettle with desired amount of
cold tap water using the water markings on the
water level display behind the handle.
ATTENTION: Make sure not to ll below the MIN
marking (= 0.8 l) so that the heat detector is co-
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
EN
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cloer 4950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cloer 4950 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info