Manual Cleanmaxx Z00513 (page 3 of 6) (English, German, Dutch, French)

703410

Zoom out

Zoom in

1/6

EN Instructions

Customer Service / Importer:

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

✆ +49 38851 314650 *)

*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.

Assembly

1. Insert the rod with the drip protec-

tion into the recess which is provid-

ed for it on the main device.

2. Fit the Y tube (1) on the rod with the

drip protection.

3. Insert the two rods (3) into the Y

tube.

4. Attach the nylon balloon (2):

– draw it over the two rods

– draw the elastic over the mounting

ﬂ ange on the main device.

The device is disassembled in the re-

verse order.

Use

1. If you have not yet done so, attach

the nylon balloon (2) (see the “As-

sembly” chapter).

The nylon balloon should sit im-

mediately below the mounting

ﬂ ange so that it can fully inﬂ ate.

2. Pull the garment which is to be pressed over the nylon balloon

and do up the zip or buttons if necessary. Make sure that

– the legs of the nylon balloon ﬁ t properly into the legs of the

trousers and are not twisted or scrunched up,

– all buttons on the garment (including the legs) are done up.

3. Spread the clamps (supplied with the main device) along the

bottom of the garment (at the front and back in each case on

the outsides) so that it is weighed down and will not go out of

shape when the nylon balloon is inﬂ ated.

4. Operate the device as described in the instructions for use of

the main device.

5. Once the nylon balloon has inﬂ ated, straighten out the garment

and smooth it down again.

6. Remove the garment from the nylon balloon after the comple-

tion of the drying/pressing process.

7. Switch off the main device, unplug it and allow it to cool.

Tips

• The drying/pressing process takes around 10 minutes for

spun-dried trousers. However, the length of time can vary

depending on the material and thickness of the material. We

recommend that you start with a shorter time and extend it if

necessary.

• In the case of trousers with a very small waist it may not be

possible to pull them over the attachment when it has already

been ﬁ tted. In this case you proceed as follows:

– push the nylon balloon (2) upwards slightly, to enable access

to the rods (3),

– remove one of the two rods from the Y tube once more (1),

– draw the trousers over the two rods,

– now replace the rods in the Y tube and

– draw the nylon balloon over the mounting ﬂ ange on the main

device again.

• Wide-apart buttons may result in the button strip crimping

slightly during pressing. Here it is advisable to smooth down

the button strip again by hand immediately after the pressing

process.

• After the drying/pressing process any creases need to be

ironed out using a normal iron.

Cleaning and Storage

Before commencing the cleaning, note the safety instruc-

tions in the “Safety Instructions” chapter and the operating

instructions for the main device!

• Clean the device if necessary with a slightly damp cloth and

a little mild detergent if required. Then wipe down fully with a

dry cloth.

• Allow all parts to dry completely before you put them away.

• Store the article in a clean, dry place that is protected from

sunlight and is not accessible to children and animals.

Disposal

Dispose of the packaging material in an environmentally

friendly manner and take it to a recycling centre. Dispose

of the article in an environmentally friendly manner as well.

More information is available from your local authorities.

Z 00513 M DS V1 0418

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cleanmaxx Z00513 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cleanmaxx Z00513 Manual

Product: