133738
18
Zoom out
Zoom in
Previous page
1/22
Next page
ENGLISH
ENGLISH
18
ENGLISH
Unpacking the appliance
Remove the appliance from the box and all the enclosed
accessories.
Do not through the packaging away, but keep it together with
the inner packing and the warranty documents for the whole
life of the warranty.
Place the appliance on smooth, level and stable work
surface.
• Do not insert the appliance plug without installing the
necessary attachments.
Installation
Installing the Exhaust Air Hose
Place the connection ring (11) over the exhaust air hose
(10). Turn the connection ring at least fi ve times in a clockwi-
se direction until it is tight. Check that it cannot be pulled off.
Push the assembled exhaust air hose from right to left
over the hose connection (9) on the back. Guide it into the
holders until it locks in place. In order to release the hose
again, press in the right-hand retainer and push the hose to
the right out of the holder.
ޥ NOTE:
If the device is in „cooling“ mode the end of the exhaust air
hose has to be led out of the air-conditioned room.
Initial Operation
Only connect the machine to a properly installed safety
socket, 230 V/50 Hz.
Make sure that the degree of protection of the socket to
which the device is connected is of at least 10 ampere!
Place the device on any heat-resistant fl at surface. Ensure
that air can enter and leave unhindered.
The distance from the air inlet grille (5/7) to the nearest wall
should be at least 20 cm. The distance from the air outlet
grille (2) to the nearest wall should be more than 1m.
Switching on/off
1. As soon as you have inserted the plug the mains control
lamp (J) lights up in red and indicates that the device is
connected to the mains.
2. Press the „ “ button (J) (13 on the remote control) to switch
the device on - the control lamp lights up in green. An
acoustic signal is heard and the digital display (E) shows
22 °C.
The device switches to the highest speed and the
„cooling“
mode (the „
“ control lamp lights up in red
and the
con
trol lamp in green). The air outlet (2) opens.
After a few seconds the device switches on automatically.
Please wait until the device has begun operation.
ޥ NOTE:
Changing the Mode of Operation
When the mode of operation is changed the compressor
remains switched off for approximately 6 minutes until the
pressure in the refrigeration circuit has eased.
Then the compressor switches on again automatically.
Cooling
If you would like to change the room temperature using the
„cooling“ mode of operation, press the „
̄
“ or „
̆
“ button
(D/F). The digital display (E) shows the temperature (min.
18°C – max. 32°C). The temperature increases or reduces
by 1°C with each press of the button.
By repeatedly pressing the „
“ button (1
8
) on the remote
control you can switch from 18, 19, 20.....32; from there it
returns to 18, 19 etc.
The device cools the room down to the set temperature,
which it then maintains. If the set temperature is above the
current room temperature, the device switches the cooling
off and only the ventilator continues running.
ޥ NOTE:
The rate at which the desired temperature is reached depends
on the temperature of the room and the outside temperature.
Ventilator Speed
In the „cooling“ and „ventilator“ modes it is possible to set 3 dif-
ferent levels for the speed of the ventilator. The speed changes
with each press of the „
“ button (G/15):
Red – for a high speed
Green – for a medium speed
Orange – for a slow speed
Timer Functions
Switch-off Timer
1. Turn the device on with the „ “ button (J/13).
2. Briefl y press the „ “ button (B/17) to change over to timer
adjustment. The digital display on the control panel fl ashes
and shows 00. The „ “ control lamp lights up in green.
3. Press the button repeatedly to programme the timer. The
length of time is increased with every press of the button by
1 hour (00, 01, 02.....24, then from the beginning again).
4. After the set time has expired the device switches off.
Switch-on Timer
Before you use the switch-on timer turn the device on and set
the mode of operation, the ventilator speed and temperature.
05-CL 3134 18 14.12.2007, 14:17:32 Uhr
Mode of Operation
Press the „
“ button (H/14) to switch the mode of operation bet-
ween “cooling” (green), „dehumidifi er” (orange) and “ventilator“
(no lamp).
Mains Lead Take-up
Unwind the mains lead from the cable holder on the rear of the
device. After using the device, please wind up the lead again.
CAUTION:
Do not move the device, as otherwise this might cause
the water to leak out and damage the fl oor, carpet or
device.
Never use the air-conditioner without protective fi lters.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clatronic cl 3134 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic cl 3134 in the language / languages: English, German, Italian as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Clatronic cl 3134

Clatronic cl 3134 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info