455925
5
Zoom out
Zoom in
Previous page
1/8
Next page
5
CLIPCLIP
SP200
ON
OFF
FRONT PANEL
1. POWER SWITCH
2. POWER LED INDICATORS
3. LIMIT LED INDICATORS
To turn the unit ON or OFF, press the Left or Right portion of
this button. Before turning on the amplifier, check all connections
and turn down the level controls.A momentary muting is normal
when turning the amplifier on or off.
(Caution: Always turn on your power amplifier last, after all your
other connected equipment, and always turn off your power
amplifier before your other connected equipment.)
These LEDs illuminate when the power is turned "ON".
These LEDs illuminate if any section of the power amplifier's
output are within 3dB of clipping. Occasional blinking of the LEDs
are acceptable, but if they remain on more than intermittently you
should turn down either the power amplifier s level controls or
reduce the output level of the preceding component to avoid
audible distortion.
These LEDs illuminate to confirm the presence of an input signal
greater than 100 mV at that channel of the amplifier
These LEDs illuminate if the power amplifier s output connection
is shorted or the load impedance is too low. When either of these
LEDs is lit up, turn OFF the power and check the output's connec-
tion to verify that it is correct, then turn ON the power again.
These control the level of signal coming into each channel. The
actual voltage gain of the amplifier is shown in dB. Turn these
controls counterclockwise if the peak LEDs illuminate steadily
(indicating too strong an input signal).
4. SIGNAL LED INDICATORS
5. PROTECT LED INDICATORS
6. LEVEL CONTROLS
61 6
4
2
3
5
10. INPUT CONNECTORS
11.L/R CHANNELOUTPUT CONNECTORS
12.BUILTIU LIMITER ON/OFF SELECTOR
13. FANS
Connect your input signal to these balanced 1/4"TRS input jacks.
Connect to your speaker box.
The fan speed is varied continuously and automatically to maintain
the proper internal operating temperature.
8
9
7
13
11
BACK PANEL
7. POWER CONNECTOR
8. FUSES
9. AC VOLTAGE SELECTOR SWITCH
The cord connector is used to connect the AC power source to
your power amplifier.
Fuse holders for (AC115V:T6.3A/250V AC230V:T3.15A/250V)
fuses. If these fuses continuously. blow, shut off the unit and have
it serviced by qualified service personnel.
Before plugging in the power cord, check to see that the unit is set
for the proper voltage for your area:~115V(60Hz)or ~230V(50Hz).
(CAUTION: DO NOT REMOVE THE CENTER GROUNDING
PIN.)
10
12
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Citronic SP Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Citronic SP Series in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info