455923
4
Zoom out
Zoom in
Previous page
1/4
Next page
With CH1 and CH2 level controls turned fully down, switch on the power to the amplifier. This product has a “soft-
start” function which makes some checks before engaging power to the amplifiers, which may take a few seconds.
With mixer (or other signal source) levels turned down, gradually increase the amplifier’s CH1 and CH2 level
controls to the required level (normally full) and then gradually increase the signal level from the mixer until sound
can be heard through the speakers and then up to the required level.
During use, the LED indicators will show if a signal is present, if half output is being produced and if the output is
reaching clip level. If the red CLIP LEDs illuminate more than very briefly, reduce the volume until they hardly light
up at all.
If the internal protection circuitry detects a fault in the speakers or amp, the amplifier will enter Protect Mode and a
“PM” LED will illuminate on the front panel to show this. Switch the amplifier off and check the entire system
(including leads) before powering up again. If still in Protect Mode, seek advice from qualified service personnel.
Before powering down, turn CH1 and CH2 level controls fully down to avoid loud noises when switching off.
SPECIFICATIONS
PL3200
PL3800
Power supply
Output: RMS @ 4
2 x 1600W
2 x 1900W
Output: RMS @ 8
2 x 915W
2 x 1100W
Bridge power: RMS @ 8
3200W
3800W
Input impedance
Output circuit architecture
Frequency response
S/N ratio
>111dB
>112dB
THD
Circuit protection
Dimensions
Weight
Troubleshooting
No power light on front panel switch
Ensure IEC is connected to mains and mains lead is in good condition
Ensure mains outlet is switched on
Power light is on but no other LEDs and not
output
Check input signal and connection leads
Ensure CH1 and CH2 level controls are not turned fully down
Power light and Signal LEDs are lit but no
output
Check speaker cabinets are not blown and are in good working order
Check speaker leads are in good condition and connected properly
PM (Protect Mode) LED is lit and there is no
output
Switch off and disconnect from mains
Check speakers are in good working order and not shorted out (using a
multi-tester)
After checking all connected items, power up again
If still in Protect Mode, switch off again and refer to qualified service
personnel
Output is very distorted and “CLIP” LEDs are
lighting
Check speaker impedance is not below rated Ohms
Turn down Input level from audio source
Switch GAIN at rear to a lower level
Turn down CH1 and CH2 level controls
Output is working but at very low level
Ensure input source is at line level
Increase input level from audio source
Turn up CH1 and CH2 level controls
Switch GAIN at rear to a higher level
Note: for further troubleshooting, refer equipment to qualified service personnel for testing
© Citronic 2011
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Citronic PL3800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Citronic PL3800 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info