Manual Char-Broil Grill2Go - X200 (page 3 of 40) (All languages)

716812

Zoom out

Zoom in

1/40

Storing Your appliance

•Clean cooking grates.

•Store in dry location.

•When gas cartridge is connected to appliance, store

outdoors in a well-ventilated space and out of reach

of children.

•Cover appliance if stored outdoors.

•Store appliance indoors ONLY if gas cartridge

disconnected, removed from appliance and stored

outdoors.

•When removing appliance from storage check for burner

obstructions.

General Appliance Cleaning

•

Apply a strong solution of detergent and

water or use a appliance cleaner with scrub brush on

insides of appliance lid and bottom. Rinse and allow

to completely air dry. Do not apply caustic

appliance/oven cleaner to painted surfaces.

Høyre

skinne

• Plastic parts: Wash with warm soapy water and wipe

dry.

Do not use citrisol, abrasive cleaners, degreasers or

a concentrated appliance cleaner on plastic parts.

Damage to and failure of parts can result.

•Porcelain surfaces: Because of glass-like

composition, most residue can be wiped away with

baking soda/water solution or specially formulated

cleaner. Use nonabrasive scouring powder for

stubborn stains.

•Painted surfaces: Wash with mild detergent or

nonabrasive cleaner and warm soapy water. Wipe

dry with a soft nonabrasive cloth.

•Stainless steel surfaces: To maintain your

appliance’s high quality appearance, wash with mild

detergent and warm soapy water and wipe dry with

a soft cloth after each use. Baked-on grease

deposits may require the use of an abrasive plastic

cleaning pad. Use only in direction of brushed finish

to avoid damage. Do not use abrasive pad on

areas with graphics.

• Cooking surfaces: If a bristle brush is used to clean

any of the appliance cooking surfaces, ensure no

loose bristles remain on cooking surfaces prior to

grilling. It is not recommended to clean cooking

surfaces while appliance is hot.

Clean appliance often, preferably after each

cookout. If a bristle brush is used to clean any of the

appliance cooking surfaces, ensure no loose bristles

remain on cooking surfaces prior to grilling. It is not

recommended to clean cooking surface while

appliance is hot.

Appliance should be cleaned at

•

IF APPLIANCE FAILS TO LIGHT

Make sure gas is turned on at cartridge.

Make sure there is gas in the cartridge.

Does the ignitor make a sparking noise?

If yes check for spark at burner.

If no spark, check for damaged or loose wires.

If wires are OK, check for cracked or broken electrode,

replace if needed.

If wire or electrodes are covered by cooking residue,

clean electrode tip with alcohol wipe if needed.

If needed replace wires.

If ignitor continues to not work then use match.

CAUTION

SPIDER ALERT!

SPIDER AND WEBS

INSIDE BURNER

If your appliance is getting hard to light or the flame

is weak, check and clean the venturis and burners.

Spiders or small insects are known to create

“flashback” problems by building nests and laying

eggs in the appliance’s venturi or burner obstructing

the flow of gas. The backed-up gas can ignite behind

the control panel. This flashback can damage your

appliance and cause injury. To prevent flashbacks

and ensure good performance, the burner and

venturi tube assembly should be removed and

cleaned whenever the appliance has been idle for an

extended period of time.

Leak Testing Valves, Tube and

Regulator

1. Turn appliance control knob to .

2. Be sure gas cartridge is tightly connected to

regulator.

. If you hear a rushing sound , remove

cartridge immediately. There is a major leak

at the connection. Correct before

proceeding.

4. Brush soapy solution (mixture of half soap and

half water) onto hose connections and areas

circled below.

5. If growing bubbles appear, there is a leak. Check

cartridge for tigthness. If leak continous relace

cartridge and try again. If leak cannot be

stopped do not try to repair. Call for replacement

parts.

Leak test at least once a year and every

time the cartridge is changed or

disconnected.

If this appliance needs to be repaired please contact

your supplier or Kriswell A/S. Please see Kriswell A/S

contact information on page 40.

Ignitor Lighting

READ INSTRUCTIONS BEFORE LIGHTING.

Do NOT lean over appliance while lighting.

1. Turn regulator control knob to postion.

2. Connect gas cartridge.

3. Open the grill lid.

4. Press and turn the regulator control knob to the

position.

5. Push ignitor button rapidly.

6. Once ignited, turn the control knob to the desired

setting.

7. If ignition does not occur in 5 seconds, turn the

regulator control knob to , wait 5 minutes, and

repeat lighting procedure.

If ignition still does not occur, follow match-lighting

instructions.

Match Lighting

1. Place lit match next to burner. Turn regulator

control knob to .

2. If ignition does NOT occur in 5 seconds, turn the

regulator control knob to , wait 5 minutes and

repeat the lighting procedure.

1. Turn gas off at regulator control knob and

disconnect gas cartridge.

2. Remove cooking grid.

3. Remove regulator from burner tube by (1) rotating

regulator until knob is to right and then (2) by pulling

outward. Shown FIG. A

4. Wipe ceramic electrode with rubbing alcohol and cloth.

Clean burner exterior with soap and water. insert

garden hose (preferably with nozzle), into burner tube

forcing water through tube. Make sure water comes

out of every porthole. Open clogged portholes with a

thin wire. Allow burner to dry thoroughly and

examine portholes. Due to normal wear and corrosion

some portholes may become enlarged, if so replace

burner. If any horizontal cracks appear from porthole to

porthole or large holes (other than portholes) are found

replace burner.

5. If barbecue is to be stored, coat burner lightly with

cooking oil. Wrap in protective cover to keep insects

out. If not storing use following steps.

6. Reattach regulator.

7. Replace cooking grid.

8. Before cooking again on barbecue, perform a “Leak

Test” and “Burner Flame Check”.

Cleaning The Burner Assembly

Regulator/Valve Installation/Removal

1. With knob pointing to right, insert Regulator/Valve

into end of burner (A)

Notch in Regulator/Valve MUST engage dimple

in end of burner.

2. Once Regulator/Valve has completely engaged

burner, turn Regulator/Valve counterclockwise (B)

to lock in position with knob pointing as shown (C).

3. To remove reverse steps.

least once a year.

Full engagement

Dimple

Red notch

Match Light Hole

Regulator locked in OFF position. Turn to to unlock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Char-Broil Grill2Go - X200 in the language / languages: All languages as an attachment in your email.

The manual is 25,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Char-Broil Grill2Go - X200 Manual

Product: