564100
4
Zoom out
Zoom in
Previous page
1/4
Next page
EN - Wireless doorbell
(84200, 84202, 84203, 84210, 84211)
Install the receiver (Chime unit) :
Open the battery case, put 3x 1,5V AA batteries (not incl.) and close.
Install the transmitter (Bell push unit) :
To match IP44 standard. Transmitter must be
xed with LED on top, Push
Button on bottom.
- Mounting the bell push button : Unclip the cover from the bell push unit and
using the 2 holes on the back of the Bell as a template (pierce holes as required),
mark and drill the fixing holes and then attach the bell push using the screws
provided. Close back the front cover to complete the whole push button bell
transmitter.
- Self Adhesive strips : Make sure the surface is free from dirt and grease. Atach
the self adhesive tab to the back cover of the push button unit. Remove the
protective strips from the self adhesive tab and push firmly against the door
frame or wall.
Link Code :
1° Choose the desire ringtone and the desire volume.
2° Bring the transmitter near the receiver, push the socket learning button once.
3° Receiver led will blink slowly, push the transmitter button.
4° Receiver
beeps twice, code is confirmed and led stops blinking.
Operating :
When Receiver (chime unit) receives a signal from the transmitter, the green LED
light will start to flash continuously for 15 seconds and ringtone sounds simulta
neously.
Receiver (chime unit) can be control by max. 6 transmitters due to max. 4 memo
-
ries with di
erent ringtone and volume for each transmitter (5 Multi-ringtone
Plug-in Door Chime, 4 interval volume control).
When the first ringtone is sounding, the receiver chime unit receives the nex
t
single from another transmitter, the LED light continuous flashing while ringtone
is changed with earlier scene setting.
Delete a code :
1° Push the learning button on receiver once, led blinks slowly.
3° Push the transmitter button.
4° Receiver connected lamp will blink twice, code is deleted and led stops
blinking. Repeat Link steps for re-setting.
Delete all memories :
1° Push the learning button on receiver for 6 seconds, led blinks.
2° Release and push again once.
3° Receiver connected lamp will blink twice, memory is erased and led stops
blinking.
* ALL PROGRAMMED MEMORY WILL BE DELETED.
Fault finding:
No activation : Check battery polarity or running out battery. Check code
program sucessful.
Caution:
Do not place two receivers near each other, the distance should be above 1
meter. Transmission distance can be reduced depending on
wall thickness or wireless environment.
www.chacPOCFt"TTJTUBODFt5ÏMÏDIBSHFNFOUt 8420 /84202 /84203 /0 /84210 /84211
Hereby CHACON declares that the devi
ce is in conformity with the essential requirements
and the other relevant disposals of the directive 1999/5/CE:.
IMPOR5"/5%Jrective 2002/96/EC WEEE) :
During the sorting of your waste, we ask you to respect the
r
egulations in e
ect regarding their elimination.
We thank you for depositing them in a place allowed to
this purpose and respecting the environment.
You can choose the volume anytime by pushing the ‘Volume’ button (4 levels :
mute, low, middle, high).
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chacon 84210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chacon 84210 in the language / languages: English, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info