564062
5
Zoom out
Zoom in
Previous page
1/5
Next page
EN – Module & Remote control
(54754, 54753)
Install the module with DC Motor (24V or other):
1° Cut o main power before installing and wiring the module.
Connect shutter to the module : shutter A+’ wires to the ‘UP port, ‘B+’ wires to the
‘DOWN ’ port, and wire DC (24V-) to shutter.
Wire AC power line to the module : AC supply 230V ‘Live’ wire to ‘L port and AC supply 230V
‘Neutral’ wire to ‘N’ port.
4° Connect COM’ port to DC (24V+). This wire should be more than 0.75mm².
5° Connect AC earth wire to earth.
6° Connect main power on, green LED lights on.
7° Link the module to transmitter (see Link a code).
Install the module with AC Motor (230V) :
1° Cut o main power before installing and wiring the module.
2° Connect shutter to the module : shutter two ‘Live wires to the ‘ ’ ports (one for up and
one for down), and shutter Neutral wire to ‘N’ port.
Wire AC power line to the module : AC supply 230V ‘Live’ wire to ‘L port and AC supply 230V
‘Neutral’ wire to ‘N’ port.
4° Connect ‘L port to ‘COM’ port. This wire should be more than 0.75mm².
5° Connect shutter earth wire to AC earth wire.
6° Connect main power on, green LED lights on.
7° Link the module to transmitter (see Link a code).
Install the module with existing DC system with wired wall switch :
1° Cut o main power before installing and wiring the module.
2° Connect module to the system : two ‘Live’ wires to the ‘ ’ module ports (one for up and
one for down), and third wire to ‘COM’ module port.
Wire AC power line to the module : AC supply 230V ‘Live’ wire to ‘L port and AC supply 230V
‘Neutral’ wire to ‘N’ port.
4° Connect AC earth wire to earth.
5° Connect main power on, green LED lights on.
6° Link the module to transmitter (see Link a code).
Install the module with existing AC (230V) system with wired wall switch :
1° Cut o main power before installing and wiring the module.
2° Connect module to the system : two ‘Live wires to the ‘ ’ ports (one for up and one for
down), shutter and supply Neutral wires to ‘N’ port, and switch and supply Live wires to ‘L
port.
3° Connect ‘L port to ‘COM’ port. This wire should be more than 0.75mm².
4° Connect earth wire to earth.
5° Connect main power on, green LED lights on.
6° Link the module to transmitter (see Link a code).
Install the transmitter.
Link Code :
1° Push the module learning button once. Module led blinks slowly.
2° Push the transmitter ON button. (If 54583 : slide learn switch from ‘Del’ to ‘Set’).
3° Module led blinks quickly twice, code is confirmed and led stops blinking.
Operation :
Push On (O) button tu open up (close) the sun blind.
Push On (O) when no the way opening up (closing down) to stop movement.
If you want to reverse the sens of commands, reverse the UP and DOWN wires on installation.
Delete a code :
1° Push the learning button on module once, led blinks slowly.
2° Push the transmitter OFF button. (If 54583 : slide switch from ‘Set’ to ‘Del’).
3° Module led blinks quickly twice, code is deleted and led stops blinking.
Repeat Link steps for re-setting.
Delete all memories :
1° Push the learning button on module for 6 seconds, led blinks.
2° Release and push again once.
3° Module led will blink twice, complete memory is erased and led stops blinking.
Receiver has 6 memory settings :
Receiver can learn from maximum 6 dierent transmitters or channels. If memory is full, you
have to delete one or all codes.
Receiver can be programmed individually or combined with other receivers (for example,
one remote control controls only the sun blind, and another switch controls both sun blinds
and lamp (connected to another Chacon module).
Fault finding:
No activation : Check code program sucessful. Check the module fuse. Check memory is not
full.
Caution:
Do not place two receivers near each other, the distance should be above 1 meter. Transmis-
sion distance can be reduced depending on wall thickness or wireless environment.
Warning! Do not use in samp places. Disconnect main power before wiring installation and
fuse changing. DO NOT OVERLOAD.
www.chacPOCFt"TTJTUBODFt5ÏMÏDIBSHFNFOUt 54754 /54753
Hereby CHACON declares that the device is in conformity with the essential requirements
and the other relevant disposals of the directive 1999/5/CE:.
IMPOR5"/5%Jrective 2002/96/EC WEEE) :
During the sorting of your waste, we ask you to respect the
r
egulations in e
ect regarding their elimination.
We thank you for depositing them in a place allowed to
this purpose and respecting the environment.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chacon 54754 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chacon 54754 in the language / languages: English, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info