667024
3
Zoom out
Zoom in
Previous page
1/40
Next page
ENGLISH | 3
ASSEMBLING YOUR TELESCOPE
Fig. 4
THE MOUNT
The ExploraScope mount and tripod come fully assembled, so setting it up is easy.
1. Remove the tripod and mount from the box.
2. Loosen the hand knobs at the bottom of each leg and extend the inner section of
the leg to the desired length. Tighten the knobs to secure the legs, being careful
not to over tighten.
3. Stand the tripod upright and pull the tripod legs apart until the center brace snaps
into place.
4. Place the threaded post on the bottom of the accessory tray over the hole in the
middle of the leg support bracket and turn the entire tray clockwise until the tray sits fi rmly against the leg brace (Fig. 1).
5. Make sure the leg hinge bolts are secure by snugging down the black thumbnuts at the top of each leg.
THE TELESCOPE TUBE
To attach the telescope tube to your tripod and mount:
1. Locate the slow motion rod guide on the side of the U-shaped mount.
Loosen the set screw in the guide until the hole through the guide is
unobstructed.
2. Holding the telescope tube above the mount, slide the slow motion
rod through the guide on the mount and gently lower the hinges
on the sides of the telescope tube into the cradles at the top of the
U-shaped mount (Fig. 2).
3. Tighten the set screw on the guide to hold the telescope
in place
4. Insert the two telescope tube mounting bolts through the tops of
the U-shaped mount and into the hinges on the sides of the telescope
tube. Do not over tighten (Fig. 3).
NOTE:
The 70mm refractor is shown, but the 114 mm Newtonian attaches to the mount in the same exact way.
THE STAR DIAGONAL
(FOR 60 MM, 70 MM AND 80 MM REFRACTORS ONLY)
The star diagonal attaches to the back of a refracting telescope that contains a small mirror that re ects the light at a 9
angle, providing a more comfortable viewing position. It also gives you a 100% correctly oriented image allowing you to
easily use this telescope for daytime terrestrial observing.
1. Remove the caps from both sides of the diagonal.
2. Loosen the setscrews on the back of the focuser and pull out
the small dust cap.
3. Insert the smaller tube on the diagonal into the back of the
focuser and secure it by tightening the setscrews (Fig. 4).
You can rotate the diagonal to any position by loosening the setscrews.
Fig. 3
Fig. 2
Fig. 1
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron EXPLORASCOPE 80AZ - 22102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron EXPLORASCOPE 80AZ - 22102 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info