580485
28
Zoom out
Zoom in
Previous page
1/32
Next page
28
Aligning the Primary Mirror
Now adjust the primary mirror screws to re-center the reflection of the small secondary mirror, so it’s silhouetted
against the view of the primary. As you look into the focuser, silhouettes of the mirrors should look concentric.
Repeat steps one and two until you have achieved this.
Remove the collimating cap and look into the focuser, where you should see the reflection of your eye in the
secondary mirror.
Newtonian collimation views as seen through the focuser using the collimation cap
Secondary mirror needs adjustment.
Primary mirror needs adjustment.
Both mirrors aligned with the collimating
cap in the focuser.
Both mirrors aligned with your eye
looking into the focuser.
Figure 7-1
Night Time Star Collimating
After successfully completing daytime collimation, night time star collimation can be done by closely
adjusting the primary mirror while the telescope tube is on its mount and pointing at a bright star. The
telescope should be set up at night and a star's image should be studied at medium to high power (30-60
power per inch of aperture). If a non-symmetrical focus pattern is present, then it may be possible to
correct this by re-collimating only the primary mirror.
Procedure (Please read this section completely before beginning):
To star collimate in the Northern Hemisphere, point at a stationary star like the North Star (Polaris). It can
be found in the north sky, at a distance above the horizon equal to your latitude. It’s also the end star in the
handle of the Little Dipper. Polaris is not the brightest star in the sky and may even appear dim, depending
upon your sky conditions.
Prior to re-collimating the primary mirror, locate the collimation screws on the rear of the telescope tube.
The rear cell (shown in Figure 7-1) has three large thumbscrews which are used for collimation and three
small thumbscrews which are used to lock the mirror in place. The collimation screws tilt the primary
mirror. You will start by loosening the small locking screws a few turns each. Normally, motions on the
order of an
1
/
8
turn will make a difference, with approximately a
1
/
2
to
3
/
4
turn being the maximum required
for the large collimation screws. Turn one collimation screw at a time and with a collimation tool or
eyepiece see how the collimation is affected (see the following paragraph below). It will take some
experimenting but you will eventually get the centering you desire.
Secondary
Mirror
Primary
Mirror
Mirror Clip
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron AstroMaster 130 EQ-MD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron AstroMaster 130 EQ-MD in the language / languages: English as an attachment in your email.

The manual is 10 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Celestron AstroMaster 130 EQ-MD

Celestron AstroMaster 130 EQ-MD User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info