538695
2
Zoom out
Zoom in
Previous page
1/2
Next page
SET
(
on back
)
Completes setting
Return to measuring
Increases the figure
Rapidly increases the figure
L
Changes the
display as in
the right figure
Resets data
(In MX or DST
display)
In ODO display:
Wheel Size Setting
SPD
ODO
MX
DST
SET(on back)
Press
simultaneously
SET(on back)
How to Replace Battery
When the display becomes dim, the battery is at the end of its
useful life. Replace it with a new lithium battery (CR2032) with the
(+) pole upward. After replacing battery, be sure to perform "All
Clear" operation and set the scale and wheel size again, as in the
"Main Unit Preparation".
In Ordinary Display
When you start/stop riding, the unit
automatically starts/stops measuring.
While measuring, the scale symbol "k" or "m" flashes.
All Clear
Operation
• Don't pay too much attention to your computer functions while riding. Keep your eyes
on the road and give due consideration to safe riding.
• Securely attach the magnet, sensor and bracket to your bicycle. Periodically check if
the screws and secure bands have loosened.
• Safely dispose of the old battery. Do not place it within children's reach. If swallowed
by mistake, consult a doctor immediately.
Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.
• For cleaning, use neutral detergent on soft cloth, and wipe off with dry cloth. Do not
apply paint thinner, benzine or alcohol, to avoid damages on the surface.
• If there is mud, sand or the like clogged between the button and the body, the move-
ment of the button may be deteriorated. Softly wash away such objects with water.
SPD Current Speed
0.0(4.0) - 100 km/h ±1 km/h [0.0(3.0) - 60 mph ±1] (under 60 km/h)
The data is updated once a second.
When it reaches 60km/h (or 60mph), the decimals are omitted.
ODO Total Distance (Odometer)
0.0 - 9999.9 km [mile] ±0.1 km [mile]
Continuously measured until battery wears down.
At 9999.9 km, it returns to zero and counting begins anew.
MX Maximum Speed
0.0(4.0) - 100 km/h ±1 km/h [0.0(3.0) - 60 mph ±1]
Displays the highest recorded speed. When it reaches 60 km/h (or 60
mph), the decimals are omitted. With reset operation, it returns to zero.
DST Trip Distance
0.00 - 999.99 km[mile] ±0.01 km[mile]
The trip distance from start to current point is displayed. With reset op-
eration, it returns to zero.
Power Saving Function
When the main unit does not receive a signal, or a button has not been
pressed for about 70 minutes, the power supply is shut down and only
mode mark flashes . By pressing the Main button, or by receiving signal,
this function is released.
Trouble Shooting
No display.
Has the battery in the main unit worn out?
Replace it with a new one.
Incorrect data appears.
Do "All Clear" operation.
Current speed does not appear. (When current speed does not appear, first short-circuit
the contact on the back with metal; if the speed display appears, the main unit is normal
and the problem must be in the bracket or the sensor.)
Is there anything on the contact of the main unit or of the bracket?
Wipe the contact clean.
Is the distance between the sensor and the magnet too far?
Are the marking line of the sensor and the center of magnet aligned?
Adjust the position of the sensor and magnet again.
Is the wire broken?
Replace it with a new one.
Current speed does not appear in wet condition.
Wipe the contacts with dry cloth. Contacts can also be treated with a water repellent
silicon jell from an automotive parts store or hardware store. Do not use industrial
water repellent; it may damage the bracket.
A.Data Display
B.Mode Symbol
C.Scale Symbol
D.Main Button
E.SET Button
F. Battery Case Cover
G.Contact
1 Bracket
2 Wire
3 Sensor
4 Magnet
5 Bracket
Rubber Pad
6 Nylon Ties
How to Install
nylon tie
pull
3
4
magnet
spoke
sensor
sensor's
marking
line
magnet's
center
clearance (2mm)
Align the magnet's center
and the sensor's marking
line. Make sure of 2mm
clearance between the
magnet and sensor. Tem-
porality attach the sensor
to the fork with the self-ad-
hesive patch.
Test
Slide the main unit onto the
bracket according to ''How to At-
tach Main Unit to Bracket" (be-
low). Spin the front wheel and
check if the scale symbol
flashes. (If not, adjust the relative
positions of the magnet and sen-
sor again.) After the test, remove
the main unit.
Fix the sensor with the nylon ties.
Note: Fasten the ties securely.
brake cable
wire
nylon ties
bracket
rubber pad
Secure the wire along the fork with
the nylon ties, and wind it round the
brake cable up to the handlebar.
Note: Allow enough wire length in
the area marked with
in
the illustration, to insure full
movement and unhindered
operation of the handlebar.
Slide the main
unit onto the
bracket from front un-
til it clicks into position.
To remove it, pull it off
forward while pushing
down the lever.
close
open
Just press
Hold down
Button Operation
Specifications
Applicable Wheel Circumference -- 112cm - 255cm (initial figure: 205 cm)
The length of the wire -------------- 70cm
Power Supply ------------------------ Lithium Battery (CR2032) x 1
Battery Life ---------------------------- Approx. 3 years
(The life of the first factory-loaded battery may be
shorter than this period.)
Dimension/Weight ---------------------- 1-25/32” x 1-9/16” x 5/8” [45 x 40 x 15.5 mm ] / 0.85 oz. [24 g]
* The specifications and design are subject to change without notice.
When using the unit for the first time or
after replacing battery, follow this procedure.
All Clear Operation
Press Main button and SET button simultaneously.
All displays illuminate, and then "k" symbol flashes.
Scale Selection
Press Main button
and select "k (km)" or "m (mile)".
Wheel Circumference Setting
Increase the figure by Main button
(to increase rapidly, hold down the button).
Press SET button to fix it
Press SET button to fix it
Preparation Completed
Main Unit Preparation
1
5
front fork
Precautions
2
How to Attach Main Unit to Bracket
INSTRUCTION MANUAL
E
In Wheel Circumference
Setting Display:
Measure the wheel circum-
ference by traveling your
bike on the ground for one
full wheel revolution. Or "Se-
lecting Values Cross Refer-
ence Table" tells you an ap-
proximate circumference
according to your tire size.
handlebar
lever
slide
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cateye CC-VL100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-VL100 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info