Manual Cateye CC-CD200N - ASTRALE 8 (page 2 of 2) (English)

508114

Zoom out

Zoom in

1/2

Power-Saving Screen

(When no signal is received for about 1 hr. the

screen switches to the power-saving mode)

When you push either of the MODE

button or the START/STOP button

or you ride the bicycle, the display

comes back to the measurement

display.

ST/STOP

MODE

SET

Speed

0.0 (4.0) - 300 km/h

[0.0 (3.0) - 185 mph]

Cadence

0.0 (20.0) - 299.9 rpm

You can program the tire size.

Return to the Elapsed Time

Range of set: 10 - 2999 mm

Increase

the number

Decrease

the number

Display for Measurements

Mode Selection Illustrations (bottom of the screen)

Cdc Cadence

0(20) - 299 rpm

Speed

0.0 (4.0) - 300.0 km/h

Average Speed

0.0 - 300 km/h

[0.0 - 185.0 mph]

Odo

Odometer

0.0 - 99999 km [mile]

Maximum speed

0.0 (4.0) - 300.0 km/h

[0.0 (3.0) - 180.5 mph]

Dst

Trip Distance

0.00 - 999.99 km[mile]

Elapsed Time

0:00’00” - 9:59’59”

Return to Clock display

When the measurements

are stopped.

When the measurements

are stopped

Clock

0:00 - 23:59

[1:00 - 12:59]

While any measurement is

displayed on the screen

Return to Elapsed

Time display

For 2 sec.

MODE

ST/STOP

MODE

Increase the number

SET

Set the hour Set the minute

Setting The Clock Time

24 hour or 12 hour system is to be used with km/h or mph

unit respectively.

Auto-mode Icon

When lit, the measurements

starts or stops

automatically.

Dst

SET

ST/STOP

MODE

ST/STOP

Specifications

Battery/Its Life : ----------------------------- A Lithium Battery (CR2032), Approx:3 yrs.

(Approx:1 hr per day usage.)

Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator)

Display : -------------------------------------- Liquid crystal display

Sensing System : --------------------------- No-contact magnetic sensor

Range of tire circumference setting : ----- 10 mm - 2999 mm (Initial value 2096 mm)

Range of Operational Temperature : ------ 0°C - 40°C (32°F - 104°F)

Dimension and Weight(Computer) : ------ 38 x 54 x 17.5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1.0 oz]

* The factory-loaded battery life might be shorter than the above-mentioned specification.

* The specifications and design are subject to change without notice.

Limited Warranty

2-Year Warranty : Computer Head Only (excluding the attached parts and deteriorated battery )

If any trouble or damage occurs during normal use, the product computer will be repaired or replaced

free of charge. Type your name, address, telephone number or e-mail address, date of purchase and

the situation of trouble and send it back together with the product to the closest address below. Trans-

portation charges shall be borne by the customer. After being repaired, the product will be shipped

back to the customer.

* Accessory parts are available for the customers as shown below.

Computer Operations

While Elapsed Time,

Trip Distance or Aver-

age Speed is displayed

Measurement

Unit Icon

Start or Stop of Measurements

The computer can be programmed to run in either MANUAL

MODE or AUTO TIME MODE. In Manual Mode you must press

the START / STOP button to turn on and off the Timer, which

records Distance and Average Speeds. In Auto Time the com-

puter turns the Timer on and off depending on a signal from the

sensor.

When speed is detected by the computer and the Timer is run-

ning, the km/h or mph will flash. Speed will appear on the com-

puter screen and the Odometer will record, regardless if the

Timer is running or not.

• Auto Time Mode (Automatic Measurement)

When the icon

is lit, the measurements are automatically

done. This is called auto-mode in which the rotation of the wheel

is detected to make the measurements start or stop automati-

cally. (When the icon

is lit, you cannot start or stop the mea-

surements by pushing the START/STOP button)

• Manual Measurements

When you don’t see the icon

on the screen, you can start or

stop the measurements by pushing the START/STOP button.

When you push the button, measurements Elapsed Time, Aver-

age Speed and Trip Distance are started, and stopped with the

second push of the button.

• How to set ON or OFF the Auto-Mode

Push the SET button while Elapsed Time (Tm) Trip Distance

(Dst) or Average Speed (Av) is displayed, then the icon

“lit” (ON) or turned OFF.

Resetting Elapsed Time, Trip Distance, Average and Max.

Speed

Push the MODE button and the START/STOP button at the same

time while the measurement other than Odometer, Elapsed

time, Maximum Speed, Average Speed and Trip Distance are

zeroed. The Odometer cannot be reset.

Open

Computer Functions

• Power-Saving Function

When no signal has been received for about 1 hr, the computer switches to the

power-saving mode and only displays the Clock. When any button is pushed or the

bicycle is riden, the measurement mode comes back.

• Selection of The Data-display Mode

In Auto-Mode you can choose between Speed or Cadence to be displayed in the top

screen.

Speed is initially selected in the upper dis-

play. When the computer is in

mode,

press the START/STOP button. Cadence

will now appear in the upper display. Speed

will be in the lower display. Switch it back

with the same procedure.

Troubleshooting

No display appears.

Is the battery dead?

Replace it and do all clear procedure.

Strange data appears

Do all clear procedure.

Data of odometer is also erased.

Measurements do not start when the START/STOP button is pushed.

Is the icon

ON?

Make the Auto-Mode off to enable the start or stop of the measurements by manual opera-

tion of the button.

No speed data (cadence) can be measured.

(If the speed data (cadence) is not displayed, have the contact

points short-circuited a few times by a metal plate. In the case

that this short-circuiting is detected by the computer, the com-

puter is considered normal and the bracket and the sensor possi-

bly have the cause of trouble.)

Is the gap between the sensor and the magnet too big?

(should be within 5 mm)

Does the marked line of the sensor align with the center of

the magnet?

Adjust the position of the magnet and the sensor.

Make sure that the contact points of the bracket or of the main body are free from dirt.

Wipe the contact points clean.

Is the cord not broken? Even if the outside of the cord looks normal, a breakage in the wire can occur.

Replace the bracket and sensor set with a new one.

Maintenance

• To clean the computer or the attached parts, use diluted neutral

detergent on a soft cloth and wipe it off with a dry cloth.

Replacing The Battery

When the display becomes dim, replace the battery.

• Put a lithium battery CR2032 in the computer with the (+) mark

facing up.

• After replacing the battery, do the necessary set-up of the com-

puter in accordance with the “Computer Set-up”.

Standard Parts

Optional Parts

#169-9400

Bracket Sensor Kit

#169-9757

Attachment Kit

#169-9691

Wheel Magnet

#166-5150

Lithium Battery (CR2032)

#169-9765

Cadence Magnet

#169-9402

Center Mount Bracket Kit

#169-9403

Bracket Sensor Kit

for Aero Bar

#169-9404

Stem Mount

Bracket Kit

#169-9760

Magnet for Composit Wheel

Is the contact points located on

the backside short-circuited in-

termittently.

Speed Cadence

Selection of the data-display mode (bottom of the screen)

Press the Mode button to navigate to each of the sub-displays listed on the right.

Press and hold the mode button for two seconds in any mode to display the Clock Time.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn.: CAT EYE Customer Service Section

Service & Research Address for United States Consumers:

CAT EYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303-443-4595 Toll Free: 800-5CATEYE

Fax: 303-473-0006 e-mail: service@cateye.com

URL: http://www.cateye.com

.,LTD.

ST/STOP

Speed Cadence

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cateye CC-CD200N - ASTRALE 8 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cateye CC-CD200N - ASTRALE 8

Cateye CC-CD200N - ASTRALE 8 User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cateye CC-CD200N - ASTRALE 8 Manual

Product: